This study investigates how the placement of transverse openings in reinforced concrete (RC) beams—necessary for utility ducts—impacts structural integrity. By comparing physical experiments with ANSYS simulations, the researchers found that openings in shear zones (near supports) significantly degrade load-carrying capacity and stiffness compared to openings in flexure zones.
What Problem Does This Paper Address?
In modern multi-story construction, a massive network of pipes and ducts (water, HVAC, electrical) must traverse the building. Traditionally, these are placed underneath beams, which increases the required floor-to-floor height and, consequently, the overall building height and cost.
Creating "holes" through the beams allows for a more compact design but introduces a structural headache. These openings create abrupt changes in the beam's cross-section, leading to high stress concentrations, reduced stiffness, and complex failure modes. This paper seeks to quantify how the specific horizontal position of these openings affects the beam's behavior under combined bending (flexure) and shear forces.
Methods
The researchers employed a dual-track approach:
Experimental Testing: They cast five RC beam specimens (0.15m x 0.15m x 0.70m) using M-25 grade concrete.
Control: Two beams without openings.
Variables: Three beams with 90mm diameter circular openings (created using PVC pipes) placed at the left corner, right corner, or both corners.
Testing: All specimens were tested using a Universal Testing Machine (UTM) to measure load-deflection and observe crack patterns.
Finite Element Analysis (FEA): The beams were modeled in ANSYS 2022 R2. This allowed the team to visualize internal metrics that are difficult to measure physically, such as directional deformation, principal stresses, and axial forces within the longitudinal rebars and stirrups.
The reinforcement followed standard codes (IS-456:2000), utilizing four 10mm diameter main bars and 8mm stirrups spaced at 100mm.
Datasets
The study did not use external datasets. Instead, it generated a primary dataset from:
Experimental results: Load (kN) vs. Deformation (mm) for the five physical specimens.
Simulation results: Numerical data and stress heatmaps generated via the ANSYS software.
Key Insights and Ideas
The "Shear Zone" Danger: The most critical insight is that placing holes in the shear zone (near the supports) has a much more detrimental impact on performance than placing them in the flexure zone (the center of the span).
Shape Matters: The authors advocate for circular openings over rectangular ones. Circular geometry avoids the sharp 90-degree corners that act as "stress raisers," which typically trigger early cracking.
Stiffness vs. Strength: Even before a beam reaches its breaking point, the presence of an opening significantly reduces its stiffness. This leads to "excessive deflection," which might not cause a collapse but can lead to serviceability failures like cracked partitions or aesthetic issues.
Reinforcement is Key: The study emphasizes that if an opening is necessary, special reinforcement detailing is required to redistribute the internal forces that the "missing" concrete would have carried.
Key Results
The quantitative drop in performance when adding openings was stark:
Control Beams (No Openings): Sustained a maximum load of 100.5 kN with a deformation of approximately 2.6–2.8 mm.
Single Corner Opening: The load capacity plummeted to 49.55 kN—a reduction of over 50%.
Double Corner Openings: This configuration was the weakest, failing at 42.45 kN and exhibiting the highest deformation (7.09 mm).
Validation: The ANSYS simulations generally mirrored the experimental trends, although the software tended to underestimate the maximum deformation in the most compromised beams (e.g., predicting 1.03 mm for the double-opening beam vs. the 7.09 mm observed physically).
Limitations and Future Work
The study focused on a relatively small beam size and a single opening diameter (90mm). The authors acknowledge that the definition of "small" vs. "large" openings remains somewhat subjective in literature.
Future research directions include:
* Testing different opening shapes (rectangular, diamond, or irregular) to find optimal geometries.
* Investigating strengthening techniques, such as using Fiber Reinforced Polymer (FRP) wraps or internal steel "trimmer" bars around the opening to recover lost load capacity.
* Developing more simplified design equations for engineers to use in practice without needing complex FEA for every hole.
Summary updated
Abstract
The provision of transverse openings in floor beams to facilitate the passage of utility pipes and service ducts results not only in a more systematic layout of pipes and ducts, it also translates into substantial economic savings in the construction of a multi-storey building. To investigate the problem of openings in beams, the author initiated a research program in the early 1980s. Since then extensive research has been carried out giving a comprehensive coverage on both circular and large rectangular openings under various combinations of bending, shear and torsion. In this paper, major findings relevant to the analysis and design of such beams under the most commonly encountered loading case of bending and shear are extracted and summarized. An attempt has been made to answer the frequently asked questions related to creating an opening in an already constructed beam and how to deal with multiple openings. It has been shown that the design method for beams with large openings can be further simplified without sacrificing rationality and having unreasonable additional cost. In this research work, we analyzed the effect of position of opening in RCC beams subjected to combined flexure and shear by checking their effects on the shear and bending behavior of the beams. The considered parameters for the study are loaddeflection curve, the shape of the cracks, and the stress distribution. Grade of concrete taken as M-25. Cross-section of reinforced concrete beam is 0.15 x 0.15 x 0.70 m with circular opening of 0.09 m diameter is considered. In this study, total five numbers of specimens were tested. The parameters are: Two types of specimens considered as without opening and three types of specimens considered as with Opening at different locations, In one specimen we took opening at the left corner of beam and in other specimen, we took opening at the right corner of the beam and In One specimen we took opening in both the corners. Stirrups were used in this study to get more accurate result. The results were validated by compare the experimental test results by UTM against the software analysis results using ANSYS software and we found that reinforced concrete beams with openings of different horizontal location and reported that placing holes in flexure zone has lesser impact on the beam performance compared to when the castellation are placed in the shear zone. This study is focused on the flexure and shear behavior of beam with different openings and their parameters like Deformation, Load-Deflection, and Crack Pattern. Abstract: The provision of transverse openings in floor beams to facilitate the passage of utility pipes and service ducts results not only in a more systematic layout of pipes and ducts, it also translates into substantial economic savings in the construction of a multi-storey building. To investigate the problem of openings in beams, the author initiated a research program in the early 1980s. Since then extensive research has been carried out giving a comprehensive coverage on both circular and large rectangular openings under various combinations of bending, shear and torsion. In this paper, major findings relevant to the analysis and design of such beams under the most commonly encountered loading case of bending and shear are extracted and summarized. An attempt has been made to answer the frequently asked questions related to creating an opening in an already constructed beam and how to deal with multiple openings. It has been shown that the design method for beams with large openings can be further simplified without sacrificing rationality and having unreasonable additional cost. In this research work, we analyzed the effect of position of opening in RCC beams subjected to combined flexure and shear by checking their effects on the shear and bending behavior of the beams. The considered parameters for the study are loaddeflection curve, the shape of the cracks, and the stress distribution. Grade of concrete taken as M-25. Cross-section of reinforced concrete beam is 0.15 x 0.15 x 0.70 m with circular opening of 0.09 m diameter is considered. In this study, total five numbers of specimens were tested. The parameters are: Two types of specimens considered as without opening and three types of specimens considered as with Opening at different locations, In one specimen we took opening at the left corner of beam and in other specimen, we took opening at the right corner of the beam and In One specimen we took opening in both the corners. Stirrups were used in this study to get more accurate result. The results were validated by compare the experimental test results by UTM against the software analysis results using ANSYS software and we found that reinforced concrete beams with openings of different horizontal location and reported that placing holes in flexure zone has lesser impact on the beam performance compared to when the castellation are placed in the shear zone. This study is focused on the flexure and shear behavior of beam with different openings and their parameters like Deformation, Load-Deflection, and Crack Pattern.
BibTeX
@article{gupta2023effect,
author = {Abhinav Gupta},
title = {{Effect of Position of Opening in RC Beams Subjected to Flexure and Shear}},
journal = {International Journal for Research in Applied Science and Engineering Technology},
year = {2023},
doi = {10.22214/ijraset.2023.48503},
}