Dynamics of Small Particle Inertial Migration in Curved Square Ducts

Kyung Ha, Brendan Harding, Andrea L. Bertozzi, Yvonne M. StokesSIAM J. Appl. Dyn. Syst 2022 · OpenReview

TL;DR

This paper introduces a simplified model (ZeLF) to predict how small particles migrate within curved microfluidic ducts with square cross-sections. They identify three distinct migration behaviors based on a key parameter (κ) that balances inertial lift and secondary flow drag, offering insights into designing microfluidic devices for particle manipulation.

What Problem Does This Paper Address?

Microfluidic devices are increasingly used for separating and manipulating microscopic particles like cells and droplets. A key phenomenon is "inertial migration," where particles deviate from the main flow due to inertial forces, especially in complex geometries like curved ducts. While inertial migration in straight ducts is well-studied, understanding this behavior in 3D curved flows, particularly in square cross-sections, is crucial for designing effective separation and focusing devices. Existing models can be computationally intensive, and a simpler, yet accurate, model is needed to explore the parameter space and understand the underlying dynamics.

Methods

The authors developed a "Zero Level Fit" (ZeLF) model, a simplified approach to predict particle migration. This model combines:

  • Inertial Lift Force: Modeled by fitting the zero-level curves of the inertial lift force from previous numerical simulations of straight ducts and then multiplying by an exponential function to capture the full cross-section behavior. This method preserves the essential topology of the force field.
  • Secondary Drag Force: Approximated using Stokes' drag law applied to the secondary flow (vortices) induced by the duct's curvature. The secondary flow is modeled using a stream function derived from Navier-Stokes equations.
  • Axial Velocity: The particle's axial velocity is approximated by the background fluid velocity, assuming it quickly reaches equilibrium.

This ZeLF model is then used to simulate particle trajectories by solving a system of ordinary differential equations. The model's accuracy is validated against a more detailed numerical model.

Datasets

Not discussed in the paper. The authors primarily rely on existing numerical simulation data from reference [8] for model development and validation.

Key Insights and Ideas

  • The κ Parameter is Key: The dimensionless parameter κ, representing the ratio of secondary drag to inertial lift, is identified as a crucial bifurcation parameter that dictates the particle's migration behavior.
  • Three Distinct Regimes: The study reveals three primary migration behaviors:
  • Multi-focus (small κ): Particles migrate to multiple stable equilibrium points, typically near the sides of the duct.
  • Unique-focus (intermediate κ): Particles converge to a single stable equilibrium point, regardless of their initial position.
  • Periodic Orbit (large κ): Particles migrate to stable limit cycles, forming orbits in the upper or lower halves of the duct.
  • Topological Preservation is Crucial: The ZeLF model's success hinges on preserving the topological structure of the inertial lift force, which is essential for accurately predicting equilibrium points and migration dynamics.
  • Axial Dynamics Matter: The paper emphasizes the importance of considering the axial distance and time required for particles to focus, which is critical for practical device design.

Key Results

  • The ZeLF model accurately captures the three distinct migration regimes (multi-focus, unique-focus, periodic orbit) observed in more complex numerical simulations, with transitions occurring at specific κ values.
  • For intermediate κ (around 10-25), particles focus to a single point, and the axial distance and time required for this focusing are quantified. For instance, a duct length of approximately 300 units (dimensionless) can focus at least 95% of particles in this regime.
  • The study shows that a given duct geometry can focus a range of particle sizes, suggesting that a single device design might be used for multiple particle sizes.
  • The model demonstrates excellent agreement with detailed numerical models for small particle sizes, validating its simplified approach.

Limitations and Future Work

  • Square Ducts vs. Others: The paper notes that square ducts are not as effective for particle separation as rectangular or trapezoidal cross-sections due to less variation in focusing positions.
  • Particle Size and Bend Radius: The ZeLF model is developed for small particles and assumes a large bend radius (small ε). The accuracy may decrease for larger particles or tighter bends.
  • Future Work: The authors suggest extending this analysis to non-square ducts and non-spherical particles to explore practical particle separation. Investigating how the observation of a single device focusing multiple particle sizes holds for these more complex scenarios is also a promising direction.

Summary updated

BibTeX
@article{ha2022dynamics,
  author = {Kyung Ha and Brendan Harding and Andrea L. Bertozzi and Yvonne M. Stokes},
  title = {{Dynamics of Small Particle Inertial Migration in Curved Square Ducts}},
  journal = {SIAM J. Appl. Dyn. Syst.},
  year = {2022},
  url = {https://openreview.net/forum?id=DBNB3Pnp17},
}
Figure