Doppler shift compensation algorithm based on inverse synthetic aperture ladar in binary phase-coded signal

Mengyuan Liu, Kai Jin, Anpeng Song, Chen Xu, Min LiJournal of Physics Conference Series 2023 · DOI

TL;DR

This paper presents a novel Doppler shift compensation algorithm for Inverse Synthetic Aperture Ladar (ISAL) using binary phase-coded signals. By leveraging Digital Moving Target Detection (DMTD), the authors successfully estimate and neutralize the signal distortion caused by target motion, restoring imaging clarity that would otherwise be lost to "uncompressible" pulse results.

What Problem Does This Paper Address?

Inverse Synthetic Aperture Ladar (ISAL) is the laser-based cousin of ISAR (Radar), used for high-resolution imaging of moving targets like satellites or aircraft. To achieve high range resolution, these systems often use binary phase-coded signals. These signals are popular because they are easy to implement and avoid the "distance-Doppler coupling" issues found in other waveforms.

Block diagram of the ISAL system architecture showing the laser source, modulator, and receiver components.

However, they have a major Achilles' heel: they are incredibly sensitive to Doppler shifts. In an ISAL system, the target's motion is necessary to create the "synthetic aperture" for imaging, but that same motion introduces a Doppler shift that can make the pulse compression fail entirely. When the Doppler shift exceeds a certain tolerance, the signal becomes "uncompressible," resulting in blurry images with massive side lobes (ghosting effects) that obscure the target.

Methods

The authors propose a compensation workflow based on Digital Moving Target Detection (DMTD). Their approach treats the Doppler effect as two distinct components:

  1. Intra-pulse Doppler: The shift occurring within a single pulse, which ruins range resolution.
  2. Inter-pulse Doppler: The shift between successive pulses, which is actually the "signal" used to build the azimuthal (cross-range) image.
Flowchart of the proposed Doppler shift compensation algorithm based on DMTD.

The algorithm follows these key steps:

  • Matrix Construction: Echo data is arranged into a matrix where columns represent "fast time" (within a pulse) and rows represent "slow time" (pulse-to-pulse).
  • Fourier Analysis: A Fourier Transform is performed along the rows to extract the Doppler frequency for each distance unit.
  • Frequency-Domain Compensation: The authors construct a compensation factor in the frequency domain to specifically target and "undo" the intra-pulse Doppler shift.
  • Velocity Ambiguity Handling: The method includes a specific logic to handle "velocity ambiguity"—cases where the target is moving so fast that the Doppler shift exceeds the pulse repetition frequency.

This approach is more efficient than standard "matched filter banks," which require designing multiple complex filters for different possible Doppler ranges.

Datasets

The study relies on simulated datasets to validate the algorithm.

  • Point Target Simulation: A single point at a distance of 100m, used to measure technical indicators like side lobe ratios.
  • Extended Target Simulation: A complex model of a fighter jet to demonstrate qualitative imaging improvements.
  • Parameters: The simulation used a 1550nm laser wavelength, a 2GHz modulation frequency, and a 4GHz sampling rate.

Key Insights and Ideas

  • The "Consistency" Assumption: The core "aha" moment is that under high pulse-repetition conditions, the intra-pulse Doppler shift is consistent across multiple pulses. This allows DMTD—usually used for target detection—to be repurposed for high-precision phase correction.
  • Preserving the "Good" Doppler: A critical aspect of the method is that it compensates for the intra-pulse shift (which causes blur) while preserving the inter-pulse phase changes necessary for azimuthal imaging.
  • Side Lobe Suppression: The paper highlights that Doppler shift doesn't just shift the target's position; it "elevates" the side lobes. The DMTD method is specifically shown to push these side lobes back down to near-ideal levels.

Key Results

The simulation results demonstrated that the algorithm effectively restores signal integrity:

  • ISLR (Integral Side Lobe Ratio): In the range profile, the ISLR worsened from -14.37dB (ideal) to -11.09dB when Doppler shift was added. After applying the DMTD compensation, it was restored to -14.40dB, nearly matching the ideal state.
  • FWHM (Resolution): The resolution (Full Width at Half Maximum) remained stable at approximately 8.7cm, proving the compensation doesn't sacrifice detail to fix the blur.
  • Visual Clarity: In the fighter jet simulation, the uncompensated image was cluttered with vertical streaks and noise; the compensated image clearly defined the aircraft's silhouette, matching the "desired" noise-free model.

Limitations and Future Work

The primary limitation is that the study is entirely simulation-based. While the math is sound, real-world ISAL systems face additional challenges:

  • Atmospheric Turbulence: Laser signals are highly susceptible to "phase errors" caused by air pockets, which might interfere with the DMTD estimation.
  • Hardware Non-linearities: Real-world modulators and amplifiers may introduce distortions not captured in the ideal simulation.

The authors suggest that the algorithm is valid for both single and multiple point scenarios, implying that the next logical step would be testing the algorithm on physical hardware in a controlled laboratory or field environment.

Summary updated

Abstract

Abstract The binary phase-coded signal is used in inverse synthetic aperture ladar (ISAL) as a commonly used pulse compression signal. However, due to its sensitivity to doppler shift, it will lead to poor or even uncompressible pulse compression results. Combined with the principle of inverse synthetic aperture ladar, the doppler shift introduced by target motion will have a very significant impact, further degrading the imaging results. By using the digital moving target detection (DMTD) method, the doppler information of each distance unit is extracted by performing Fourier transform on the same distance unit, and then a compensation factor is constructed in the frequency domain to compensate for this doppler, correcting the adaptation problem brought by it and improving the imaging result.
BibTeX
@article{liu2023doppler,
  author = {Mengyuan Liu and Kai Jin and Anpeng Song and Chen Xu and Min Li},
  title = {{Doppler shift compensation algorithm based on inverse synthetic aperture ladar in binary phase-coded signal}},
  journal = {Journal of Physics Conference Series},
  year = {2023},
  doi = {10.1088/1742-6596/2525/1/012011},
}
Figure