Dislocation cross-slip mechanisms in aluminum

Congming Jin, Yang Xiang, Gang LüThe Philosophical Magazine A Journal of Theoretical Experimental and Applied Physics 2011 · DOI

TL;DR

This paper uses atomistic simulations to reveal that dislocation cross-slip in aluminum behaves differently depending on the length of the dislocation segment. Short segments follow a simple mechanism, while longer segments exhibit more complex, position-dependent cross-slip behaviors, offering new insights into plastic deformation.

What Problem Does This Paper Address?

Plastic deformation in metals, like aluminum, is heavily influenced by the movement of dislocations. A key process that governs this movement is "cross-slip," where a dislocation changes its slip plane. Understanding the mechanisms and energy barriers associated with cross-slip is crucial for predicting and controlling material properties under stress. Previous studies on cross-slip in face-centered cubic (f.c.c.) metals have proposed several models (Friedel-Escaig, Fleischer, Schoeck-Seeger), but there has been a lack of clarity on which mechanisms are operative under specific conditions, particularly concerning the influence of dislocation length and its precise position. This paper aims to systematically investigate these factors in aluminum, a material with a high stacking fault energy that might favor different cross-slip pathways compared to other f.c.c. metals.

Methods

The researchers employed atomistic simulations using the Embedded-Atom Method (EAM) potential for aluminum, specifically the Mishin potential, which is known for its accuracy in reproducing stacking fault energies. To study the rare event of dislocation cross-slip and determine the associated energy barriers, they utilized the string method. This is a well-established technique for finding the minimum energy path (MEP) between two stable states (initial and final positions of the dislocation) at zero temperature. The string method represents the transition path as a series of discrete images, which are then evolved to find the lowest energy pathway. A key novelty in this study is the systematic examination of how the relative position of the dislocation segment, both before and after cross-slip, affects the transition path and energy barrier. They explored various initial and final positions of the dislocation segment to understand this positional dependence.

Datasets

Not discussed in the paper. The study relies on atomistic simulations rather than experimental datasets for training or evaluation.

Key Insights and Ideas

  • Dislocation Length Matters: The behavior of cross-slip is not uniform; it significantly changes based on whether the dislocation segment is short or long.
  • Short Segments are Simple: For short dislocation segments, cross-slip consistently follows the Fleischer (FL) mechanism, regardless of the dislocation's initial and final positions. This mechanism involves the continuous folding of the stacking fault.
  • Long Segments are Complex and Position-Dependent: For longer segments, two distinct cross-slip mechanisms emerge, dictated by the symmetry of the dislocation's initial and final positions relative to the intersection of the primary and cross-slip planes.
  • Symmetric Cross-Slip: When positions are symmetric, the cross-slip primarily follows the Friedel-Escaig (FE) mechanism, involving the formation and movement of constrictions.
  • Asymmetric Cross-Slip is a Hybrid: When positions are asymmetric, a novel, two-step mechanism is observed. It begins with a partial fold-over characteristic of the FL mechanism, forming a stair-rod dislocation, and is then completed by the FE mechanism with asymmetrically formed constrictions. This hybrid mechanism has not been previously reported.
  • Aluminum's High Stacking Fault Energy: The close proximity of partial dislocations in aluminum (due to its high stacking fault energy) contributes to these observed mechanisms, potentially allowing for easier folding and constriction formation.

Key Results

  • Short Dislocation Segment: The cross-slip energy barrier was found to be 0.028 eV/b for short segments, following the FL mechanism. This is significantly lower than in copper.
  • Long Dislocation Segment (Symmetric 0-0 cross-slip): The energy barrier for symmetric cross-slip was 0.60 eV, following the FE mechanism.
  • Long Dislocation Segment (Asymmetric 1-0 cross-slip): The energy barrier for this novel, asymmetric mechanism was 0.66 eV. While slightly higher than the symmetric FE mechanism, it is still a significant pathway.
  • Critical Length: A critical dislocation length of approximately 22b was identified, above which the cross-slip behavior transitions from the simple FL mechanism to the more complex, position-dependent FE or hybrid mechanisms.

Limitations and Future Work

  • Zero Temperature Simulations: The simulations were conducted at 0 K. The authors acknowledge that finite temperature effects and the role of entropy in the cross-slip process are important and will be explored in future work.
  • Transition State Theory Limitations: While the string method is powerful, it relies on reasonably prescribed initial and final states and initial guesses for the MEP. The authors have addressed the position dependence, but further exploration of multiple paths and initial guesses could be beneficial.
  • Experimental Verification: Extracting quantitative cross-slip information from deformation experiments is challenging. The authors suggest that future work could explore the operative conditions for the newly identified asymmetric mechanism, such as the influence of applied stress or geometric restrictions, and potentially investigate free surface effects.
  • Finite Temperature String Method: The authors plan to employ the finite temperature string method to further confirm their findings and explore the entropy effect.

Summary updated

Abstract

We have systematically studied dislocation cross-slip in Al at zero temperature by atomistic simulations, focusing on the dependence of the transition paths and energy barriers on dislocation length and position. We find that for a short dislocation segment, the cross-slip follows the uniform Fleischer (FL) mechanism. For a longer dislocation segment, we have identified two different cross-slip mechanisms depending on the initial and final positions of the dislocation. If the initial and final positions are symmetric relative to the intersection of the primary and cross-slip planes, the dislocation cross-slips via the Friedel–Escaig (FE) mechanism. However, when the initial and final positions are asymmetric, the dislocation cross-slips via a combination of the FL and FE mechanisms. The leading partial folds over to the cross-slip plane first, forming a stair-rod dislocation at the intersection with which the trailing partial then merges via the FL mechanism. Afterwards, constrictions appear asymmetrically and move away from each other to complete the cross-slip via the FE mechanism.
BibTeX
@article{jin2011dislocation,
  author = {Congming Jin and Yang Xiang and Gang Lü},
  title = {{Dislocation cross-slip mechanisms in aluminum}},
  journal = {The Philosophical Magazine A Journal of Theoretical Experimental and Applied Physics},
  year = {2011},
  doi = {10.1080/14786435.2011.602030},
}
Figure