Abstract
Se presenta el diseño y construcción de un sistema mecatrónico automatizado para el crecimiento de películas delgadas por la técnica de recubrimiento por inmersión. El sistema consta de un porta sustrato que realiza desplazamientos verticales entre dos posiciones ajustables. El movimiento del porta sustrato es controlado por una cadena de transmisión accionada por un motor de corriente continua. Los finales de recorrido del porta-sustrato son sensados por micro-switchs colocados en los extremos del intervalo de movimiento. La adquisición de la señal de los micro-switchs y la generación de la señal de control para el motor son realizadas por una tarjeta de adquisición de datos National Instruments USB 6353. Desde una interfaz gráfica desarrollada en LabVIEW el usuario puede programar todos los parámetros del reactor, entre ellos las velocidades de inmersión y extracción de los sustratos y el tiempo de secado.
Introduction
Thin-film deposition via dip coating is a cornerstone of materials science, used for applications ranging from optoelectronics to biocompatible coatings. The thickness and homogeneity of these films depend heavily on the precision and smoothness of the substrate's movement into and out of a precursor solution. While commercial dip-coating reactors offer high precision, they often cost upwards of $10,000 USD—a significant barrier for many research labs. Furthermore, many DIY or low-cost solutions use stepper motors, which move in discrete steps. These "micro-jerks" can induce waves or ripples in the liquid, leading to uneven film thickness and increased surface roughness. This paper details the design and construction of a professional-grade, automated system using affordable components that solves these mechanical vibration issues.
System Design and Methodology
The reactor is built on a vertical aluminum frame designed for stability and precision. The core mechatronic components include:
- Actuation and Transmission: A DC motor with a gearbox was chosen over a stepper motor to ensure perfectly smooth, continuous motion. A timing belt and pulley system converts the motor's rotation into linear vertical movement for the substrate holder.
- Sensing: Two adjustable micro-switches act as limit sensors, defining the travel range of the substrate. The reactor features 15 pre-drilled holes on the vertical axis, allowing researchers to mechanically adjust the travel range to accommodate different substrate sizes and liquid volumes.
Control Hardware and Logic
The system uses an LMD18201 H-bridge for motor driving. Pulse Width Modulation (PWM) is used to control speed, while a direction (DIR) signal handles the up/down logic. A National Instruments (NI) USB 6353 data acquisition (DAQ) card interfaces the hardware with a PC running a custom LabVIEW 2009 GUI.
A key innovation in this design is the PWM generation logic. The authors used an elegant analog approach: by comparing a 12.5Hz sawtooth wave with a DC reference voltage ($V_{Ref}$) using an LM324 operational amplifier, they created a robust speed control mechanism. This allows the DAQ's analog output to easily manage the motor speed through a simple voltage reference.
Key Results and Characterization
The system's performance was validated through both operational testing and material characterization:
- Operational Range: The system achieves a linear speed range between 1.23 mm/s and 6.36 mm/s.
- Efficiency: The H-bridge power stage operates at approximately 89% efficiency.
- Precision: The positional error at the limit switches is roughly 1 mm, which is negligible for standard dip-coating applications.
- Film Quality: The system successfully produced magnetite ($Fe_3O_4$) films. AFM analysis of a 7-layer film showed a thickness of ~480 nm and a roughness of ~17 nm, indicating a very high degree of homogeneity. SEM confirmed a granular, uniform sub-micrometric structure.
Conclusion
The developed mechatronic reactor provides a high-precision, low-cost alternative to commercial dip-coating systems. By utilizing a DC motor and a custom PWM control circuit, the authors successfully eliminated the vibration issues common in stepper-motor-based designs. Future work may involve using lower-cost microcontrollers like Arduino to replace the high-end NI DAQ card and integrating additional sensors for real-time monitoring of the precursor solution's state.
Summary updated