Development of readout electronics a novel beam monitoring system for ion research facility accelerator

Honglin Zhang, Haibo Yang, Xianqin Li, Yuezhao Zhang, Xiangming Sun, Dong Wang, Ran Huang, Yao Wang, Wei Zhou, Chengxin ZhaoarXiv 2020 · DOI · arXiv

Abstract

This paper details the design and implementation of readout electronics for a novel beam monitoring system tailored for ion research facility accelerators. The system is composed of a Front-end Card (FEC) utilizing the Topmetal-II- ASIC and a Readout Control Unit (RCU) based on an FPGA. The FEC processes charge from hitting particles into voltage signals, while the RCU digitizes and manages data transmission. Laboratory characterization demonstrates high linearity and stability, confirming the system's readiness for integration into particle accelerators.

Introduction

In high-energy heavy-ion research facilities, precise monitoring of beam profiles—specifically shape and position—is essential for optimizing experimental outcomes. Traditional monitoring tools often suffer from low spatial resolution (hundreds of micrometers) or are "blocking" devices that physically obstruct the beam, preventing continuous real-time observation.

To overcome these limitations, researchers have developed a Residue Gas Ion Beam Profile Monitor (RGIPM). This non-invasive system detects electrons generated by the ionization of residual gas within the accelerator's vacuum chamber, allowing for high-precision monitoring without interfering with the beam path.

Figure 1: 3D schematic of the beam monitoring system integrated within a vacuum chamber, showing the beam path and the Topmetal-II- detector assembly.

System Architecture and Methods

The readout electronics are divided into two functional blocks: the Front-end Card (FEC) and the Readout Control Unit (RCU).

Front-end Card (FEC) and Topmetal-II- ASIC

The FEC is the primary sensing interface, housing the Topmetal-II- ASIC. This specialized silicon pixel detector features a $72 \times 72$ array. Unlike traditional sensors, the "Topmetal" pads are directly exposed to the vacuum, allowing for direct charge collection without detector leakage current. Each pixel is equipped with a low-noise Charge Sensitive Amplifier (CSA) to convert collected charge into an analog voltage.

Figure 3: Overview of the hardware components: (a) the Front-end Card, (b) micrograph of the Topmetal-II- chip, (c) diagram of a single pixel's exposed area, and (d) the readout circuit schematic.

Readout Control Unit (RCU)

The RCU, powered by a Xilinx Kintex-7 FPGA, serves as the system's central processor. It performs signal conditioning, converting single-ended signals from the FEC into differential signals to minimize noise. An 8-channel ADC (AD9252) digitizes the data at 50 Msps. The FPGA manages high-speed data alignment using a sophisticated bit-slipping procedure, DDR3 storage, and 1-Gigabit Ethernet communication with a host computer.

Experimental Validation

The system underwent rigorous laboratory testing to ensure reliability:

  • Linearity: The RCU demonstrated exceptional linearity across a -1.5V to 1.5V range, with a maximum variation of approximately 0.6%.
  • Stability: Continuous 48-hour operation tests showed no performance degradation or failures.
  • Functional Testing: Using an Alpha radiation source ($^{241}$Am) in a vacuum, the system successfully captured electron clusters, validating its ability to image ionization events similar to those expected from an ion beam.

Conclusion

The developed readout electronics provide a high-resolution, non-invasive solution for beam monitoring. By leveraging the unique direct-charge collection capabilities of the Topmetal-II- chip and the robust processing power of an FPGA-based RCU, the system achieves spatial resolutions in the tens of micrometers. Future work will focus on performance evaluation under high-intensity beam conditions and optimizing data compression schemes for real-time operation.

Summary updated

Abstract

This article presents the readout electronics of a novel beam monitoring system for ion research facility accelerator. The readout electronics are divided into Front-end Card (FEC) and Readout Control Unit (RCU). FEC uses Topmetal II minus to processes the energy of the hitting particles and convert it into a voltage signal. The main function of RCU is to digitize the analog output signal of FEC and format the raw data. On the other hand, the RCU also processes the control commands from the host and distributes the commands according to the mapping. The readout electronic has been characterized and calibrated in the laboratory, and have been installed with the detector. Implementation and testing of readout electronics have been discussed.
BibTeX
@misc{zhang2020development,
  author = {Honglin Zhang and Haibo Yang and Xianqin Li and Yuezhao Zhang and Xiangming Sun and Dong Wang and Ran Huang and Yao Wang and Wei Zhou and Chengxin Zhao},
  title = {{Development of readout electronics a novel beam monitoring system for ion research facility accelerator}},
  year = {2020},
  eprint = {2002.06216},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/2002.06216},
}

Loading related content...

Figure