Development of a New Surface Acoustic Wave Based Gyroscope on a X-112°Y LiTaO3 Substrate

Wen Wang, Jiuling Liu, Xiao Xie, Minghua Liu, Shitang He2011 · DOI

TL;DR

This paper presents a novel Surface Acoustic Wave (SAW) gyroscope utilizing the Coriolis force acting on acoustic waves propagating on a rotated X-112°Y LiTaO₃ substrate. The developed device achieves a high sensitivity of 1.332 Hz deg⁻¹ s⁻¹ with excellent linearity, addressing limitations of previous SAW gyroscope designs in terms of precision and temperature stability.

What Problem Does This Paper Address?

Traditional gyroscopes, while essential for navigation and motion sensing, can be bulky, expensive, and susceptible to shock. Surface Acoustic Wave (SAW) based gyroscopes offer a promising alternative due to their inherent shock robustness, small size, low cost, and long lifespan. However, existing SAW gyroscope designs, particularly those relying on standing-wave modes, have suffered from low precision and poor temperature stability, often due to the choice of piezoelectric substrate materials. This paper aims to overcome these limitations by developing a new SAW gyroscope that leverages the SAW gyroscopic effect on a specifically chosen substrate (X-112°Y LiTaO₃) and employs a differential dual-delay-line oscillator configuration for enhanced sensitivity and temperature compensation.

Methods

The core of this work lies in the theoretical and experimental development of a SAW gyroscope based on the gyroscopic effect.

  • Theoretical Model: The authors developed a comprehensive theoretical model for the SAW gyroscopic effect. This model utilizes the surface effective permittivity method to analyze the propagation of SAW on anisotropic piezoelectric substrates under rotation. This method simplifies the complex piezoelectric medium equations of motion by considering the effective permittivity of the substrate, providing a more tractable way to predict SAW velocity shifts due to rotation.
  • Substrate Selection: Through theoretical analysis, the rotated X-112°Y LiTaO₃ substrate was identified as offering a larger sensor response compared to other common piezoelectric substrates like ST-X quartz and 128°YX LiNbO₃.
  • Device Design: A dual-delay-line oscillator configuration was employed. Two SAW delay lines with opposite propagation directions were fabricated on the same X-112°Y LiTaO₃ chip. These lines act as feedback elements for two SAW oscillators. This differential structure is crucial for doubling the sensor's sensitivity and compensating for temperature-induced effects.
  • Transducer Design: Single-phase unidirectional transducers (SPUDT) and combed transducers were used to structure the delay lines. This choice was made to improve the frequency stability of the oscillators, a critical factor for accurate gyroscope performance.
  • Experimental Setup: A precision rate table was used to experimentally evaluate the performance of the fabricated SAW gyroscope. The sensor output was monitored using an oscilloscope and a programmable frequency counter.

Datasets

Not discussed in the paper. The paper focuses on theoretical modeling and experimental validation using fabricated devices.

Key Insights and Ideas

  • Substrate Matters: The choice of piezoelectric substrate is critical for SAW gyroscope performance. The rotated X-112°Y LiTaO₃ substrate demonstrated superior potential for enhanced sensor response due to its material properties.
  • Differential Design for Sensitivity and Stability: The dual-delay-line oscillator with opposite propagation directions effectively doubles the sensitivity and provides a mechanism for compensating temperature variations, a significant improvement over single-line designs.
  • Surface Effective Permittivity Method: This theoretical approach offers a simplified yet effective way to analyze the complex SAW gyroscopic effect, bridging the gap between theoretical predictions and experimental observations.
  • SPUDT and Combed Transducers for Stability: The use of these transducer types is key to achieving the necessary frequency stability in the SAW oscillators, which directly impacts the gyroscope's detection threshold and overall accuracy.

Key Results

  • Theoretical Prediction: The theoretical analysis indicated that the rotated X-112°Y LiTaO₃ substrate would yield a larger velocity shift, and thus a better sensor response, due to the gyroscopic effect.
  • Fabricated Device: A SAW gyroscope was successfully fabricated on an X-112°Y LiTaO₃ chip operating at 160 MHz.
  • Experimental Performance:
    • Sensitivity: A high sensitivity of 1.332 Hz deg⁻¹ s⁻¹ was achieved.
  • Dynamic Range: The gyroscope demonstrated good performance over a large dynamic testing range of up to 1,000 deg s⁻¹.
  • Linearity: The sensor exhibited good linearity in its response to angular rates.
  • Frequency Stability: The fabricated SAW oscillator showed excellent frequency stability, with short-term stability (min) of 0.05 ppm and long-term stability (h) of 0.4 ppm.

Limitations and Future Work

  • Limitations: While the paper reports excellent sensitivity and linearity, the authors do not explicitly detail limitations such as noise floor, bias drift, or long-term stability under varying environmental conditions beyond the reported frequency stability of the oscillator. The theoretical model, while effective, is based on certain approximations (e.g., small ratios of rotation velocity to frequency).
  • Future Work: The paper implicitly suggests further optimization of the device design and fabrication process. Future research could focus on:
  • Investigating the impact of different metallization thicknesses and transducer geometries.
  • Exploring advanced temperature compensation techniques beyond the differential structure.
  • Characterizing the gyroscope's performance under more rigorous environmental conditions (vibration, shock, wider temperature ranges).
  • Further refining the theoretical model to account for higher-order effects or non-linearities.

Summary updated

BibTeX
@misc{wang2011development,
  author = {Wen Wang and Jiuling Liu and Xiao Xie and Minghua Liu and Shitang He},
  title = {{Development of a New Surface Acoustic Wave Based Gyroscope on a X-112°Y LiTaO3 Substrate}},
  year = {2011},
  doi = {10.3390/s111110894},
}

Loading related content...

Figure