Design of High Speed Sampling Clock Based on LMX2531

Bing Bing Zhou, Zhengsheng Li, Hao Chen2016 · DOI

Abstract

The LMX2531 is a low power, high performance frequency synthesizer system which includes a fully integrated delta-sigma PLL and VCO with fully integrated tank circuit. The third and fourth poles are also integrated and adjustable. Also included are integrated ultra-low noise and high precision LDOs for the PLL and VCO which give higher supply noise immunity and more consistent performance. When combined with a high quality reference oscillator, the LMX2531 generates very stable, low noise local oscillator signals for up and down conversion in wireless communication devices. In the system, the LMX2531 is controlled by FPGA. It outputs a 1500MHz clock signal through programmed eleven 24-bit registers with Verilog HDL. The signal is very suitable to be used as the sampling clock of ADC in high speed acquisition systems due to its low jitter and high stability.

Introduction

In high-speed data acquisition systems—ranging from military radar to medical imaging—the performance of the Analog-to-Digital Converter (ADC) is the primary bottleneck. A critical factor in ADC performance is aperture jitter. If the clock signal fluctuates even slightly in time, it introduces noise into the sampled data, degrading the Signal-to-Noise Ratio (SNR) and reducing the Effective Number of Bits (ENOB). As sampling rates push into the Gigahertz range, designing a clock that is both high-frequency and ultra-stable becomes a significant engineering challenge. This paper addresses the need for a programmable, integrated solution that minimizes jitter while remaining flexible enough for various high-speed applications.

System Architecture and Methods

The proposed system utilizes a hardware-software co-design approach centered on the LMX2531 frequency synthesizer. This chip features a built-in Delta-Sigma Phase-Locked Loop (PLL), a Voltage-Controlled Oscillator (VCO), and ultra-low-noise Low-Dropout regulators (LDOs). These integrated LDOs are critical because they shield the sensitive timing circuits from power supply noise.

Schematic diagram of the LMX2531 frequency synthesizer circuit.

An FPGA acts as the control logic, communicating with the LMX2531 via a three-wire MICROWIRE serial interface. Custom Verilog HDL code was developed to program the LMX2531’s internal registers. A specific initialization sequence is required for the eleven 24-bit registers (starting with multiple writes to Register 5) to ensure the internal LDOs stabilize correctly. To reach the target 1500MHz output from a 50MHz crystal oscillator, the system is configured with a frequency division coefficient ($R$) of 2 and an $N$ register value of 60.

Key Results and Performance Analysis

The design was validated through high-fidelity phase noise simulations using the National Semiconductor Clock Design Tool. The system successfully generated a stable 1500MHz clock with impressive noise floor performance.

Phase noise display and jitter analysis for the 1500 MHz output.

As shown in the simulation results, the phase noise characteristics are as follows:

  • -101.28 dBc/Hz at 1 kHz offset.
  • -121.41 dBc/Hz at 100 kHz offset.
  • -161.96 dBc/Hz at 10 MHz offset.

The total RMS jitter was calculated at approximately 234.6 femtoseconds (fs). In the context of high-speed sampling, sub-picosecond jitter is a hallmark of a high-quality clock source, ensuring minimal impact on the ADC's dynamic range.

Conclusion

The LMX2531-based design provides a robust, programmable solution for high-speed clock generation. While the simulation results are promising, showing sub-picosecond jitter and excellent phase noise, future work will involve physical fabrication and empirical testing to verify performance under real-world conditions, such as thermal drift and PCB trace impedance mismatches. The FPGA-controlled architecture remains a versatile choice, capable of supporting output frequencies between 553MHz and 3132MHz.

Summary updated

Abstract

The LMX2531 is a low power, high performance frequency synthesizer system which includes a fully integrated delta-sigma PLL and VCO with fully integrated tank circuit. The third and fourth poles are also integrated and also adjustable. Also included are integrated ultra-low noise and high precision LDOs for the PLL and VCO which give higher supply noise immunity and also more consistent performance. When combined with a high quality reference oscillator, the LMX2531 generates very stable, low noise local oscillator signals for up and down conversion in wireless communication devices. In the system, the LMX2531 is controlled by FPGA. It outputs a 1500MHz clock signal through programmed eleven 24-bit registers with Verilog HDL. The signal is very suitable to be used as the sampling clock of ADC in high speed acquisition system for it has the characteristics of low jitter and high stability.
BibTeX
@misc{zhou2016design,
  author = {Bing Bing Zhou and Zhengsheng Li and Hao Chen},
  title = {{Design of High Speed Sampling Clock Based on LMX2531}},
  year = {2016},
  doi = {10.2991/iccia-16.2016.76},
}
Figure