Design of Disaster Relief Robot Assistant

Chao Liu, Xu Guangxian, Feng Gao, Nan XuAdvances 2013 · DOI

Abstract

In the aftermath of natural disasters or terrorist activities, the "golden hour" for rescue is extremely limited. This paper presents the design of an autonomous intelligent robot controlled by an S3C2410 MCU. The system utilizes a wireless network card and UDP protocol to receive commands and transmit real-time video, environmental data (temperature, humidity, methane), and GPS coordinates to a host system, facilitating efficient search and rescue operations in hazardous ruins.

Introduction

Disaster environments, such as collapsed buildings or mines, are often inaccessible or too dangerous for human rescuers. While traditional robots exist, wheeled variants struggle with debris, and legged variants are often slow. This research addresses the need for a versatile, hybrid locomotion system that combines the speed of wheels with the obstacle-clearing capabilities of a six-legged bionic structure, modeled after the anatomy of an ant.

System Architecture

The system is divided into two main components: the Walk Detection Robot and the Control Display Terminal, communicating via a wireless LAN.

System architecture showing the interaction between the robot and the control terminal.

Hardware Design

The robot's "brain" is an S3C2410 (ARM9) processor running at 203MHz, which manages high-level data processing and network communication. To ensure precise movement, a secondary ATmega16 (AVR) microcontroller is used as a dedicated servo controller, handling 11 channels of PWM signals for the robot's legs and steering. The sensor suite includes a USB camera for visual feedback, sensors for temperature, humidity, and methane, and a GPS module for localization.

Software and Communication

The robot runs on Linux 2.6.24. The control interface is developed using the Qt (QTE) framework. For communication, the UDP protocol was selected over TCP to prioritize low-latency video transmission, essential for real-time remote navigation.

Gait Control Strategy

The robot employs a "composite mode" locomotion strategy, switching between wheeled and legged movement based on the terrain's complexity.

Flowchart of the gait control algorithm and obstacle detection logic.

The control logic evaluates obstacle height ($\Delta v$) against specific thresholds:

  1. Wheeled Mode: Used when ground irregularities are minimal ($\Delta v < \Delta y$).
  2. Climbing Mode: Activated when obstacles are within the leg's reach ($\Delta y < \Delta v < \Delta x$).
  3. Avoidance Mode: Triggered if an obstacle is too high to climb ($\Delta v > \Delta x$).

Key Results

Functional testing demonstrated the system's viability for disaster relief:

  • Real-time Video: The system achieved a stable transmission of 20 frames per second at a resolution of 320x240.
  • Network Performance: The 54Mbps WiFi link successfully handled concurrent streams of video and sensor data.
  • Locomotion: The robot successfully transitioned between modes to navigate obstacles, with control latency remaining within acceptable limits for remote operation.

Conclusion and Future Work

The hybrid wheel-leg design provides a balanced solution for navigating unstructured disaster environments. Future developments will focus on improving signal robustness in concrete-heavy ruins using WiFi relay modules, developing a formal kinematic model for optimized movement, and increasing image resolution and battery endurance.

Summary updated

Abstract

In the world, the disasters often occur due to natural disasters, terrorist activity and other reasons, and the rescuers only have a very short time in the ruins to find survivors in disaster relief, or their survived chances are nearly nil. In this dangerous environment, robotics can help rescued workers. Autonomous intelligent robots will be used for search and rescue. It responds to a lot of work effectively, quickly and reliably. Robot will be mastered by the MCU of S3C2410. Specific function through the UDP controls the robot via a wireless network card to receive the control command, and the camera captures the real-time video, life detector, temperature and humidity and GPS coordinates transferred back to host system to achieve the purposes of relief disaster.
BibTeX
@inproceedings{liu2013design,
  author = {Chao Liu and Xu Guangxian and Feng Gao and Nan Xu},
  title = {{Design of Disaster Relief Robot Assistant}},
  booktitle = {Advances},
  year = {2013},
  doi = {10.2991/wiet-13.2013.21},
}
Figure