TL;DR
This paper presents a novel, ultra-low power CMOS temperature sensor for passive RFID tags that directly converts temperature variations into a digital output using a Phase-Locked Loop (PLL) architecture, eliminating the need for an external reference clock. This design achieves a power dissipation of just 92 nW and a small area of 0.021 mm², making it highly suitable for battery-less RFID applications.
What Problem Does This Paper Address?
The Internet of Things (IoT) relies heavily on technologies like RFID and Wireless Sensor Networks (WSNs). Integrating sensors with RFID tags can imbue otherwise "dumb" objects with sensing capabilities. However, passive RFID tags, which harvest energy from readers, have extremely stringent power constraints. Traditional CMOS temperature sensors often consume too much power (mW range) for these applications, and even low-power digital conversion methods typically require an external reference clock, which further degrades power and accuracy. This paper addresses the need for a highly integrated, ultra-low power, and self-contained temperature sensor for passive RFID tags that can directly output digital temperature readings without external components.
Methods
The core innovation lies in the sensor's architecture, which employs a Phase-Locked Loop (PLL) to achieve temperature-to-digital conversion. This PLL-based sensor has two main blocks:
- Frequency-Modulating Block (Temperature-Controlled Oscillator - TCO): This block directly converts temperature variations into a corresponding frequency ($f_t$). The TCO is designed using a current-starved ring oscillator, where the current source is a Proportional To Absolute Temperature (PTAT) current. This PTAT current is generated using a PV-compensated circuit that ensures stable current output despite variations in process and supply voltage.
- Frequency-Demodulating Block (Digital First-Order PLL): This block takes the temperature-controlled frequency ($f_t$) and converts it into a digital output. It consists of a 1-bit Phase Detector (PD) and a Digitally-Controlled Oscillator (DCO). The DCO is also a current-starved ring oscillator, but its current source is constant. The PLL locks the DCO's frequency ($f_{dco}$) to the TCO's frequency ($f_t$). The output of the PD, a 1-bit signal, effectively quantizes the frequency difference and, when over-sampled, represents the digital temperature value. This architecture is described as a frequency-to-digital $\Sigma\Delta$-modulator.
The design utilizes a TSMC 0.18 µm 1P6M mixed-signal CMOS process. The current-starved ring oscillators are implemented with a reduced voltage swing on internal nodes to minimize dynamic power consumption.
Datasets
Not discussed in the paper. The evaluation relies on measurements from fabricated chips and simulations.
Key Insights and Ideas
- PLL for Temperature Sensing: Using a PLL as a frequency-to-digital converter for temperature sensing is a novel approach that bypasses the need for ADCs and external clocks, directly yielding a digital output.
- PTAT Current for Temperature-Frequency Conversion: Generating a PTAT current is crucial for making the TCO's output frequency directly proportional to temperature. The PV-compensated PTAT current source design is key to achieving stable operation.
- Current-Starved Oscillators for Low Power: Employing current-starved ring oscillators with reduced internal node voltage swings significantly cuts down power consumption, a critical factor for passive RFID tags.
- Self-Referencing Nature: The PLL's feedback loop inherently compares two oscillators, making the system sensitive to relative frequency differences rather than absolute values. This design inherently cancels out common-mode variations from supply voltage and temperature fluctuations affecting both oscillators, leading to improved accuracy and requiring only 1-point calibration.
Key Results
- Power Dissipation: Achieves an ultra-low power dissipation of 92 nW at a 1.0 V supply voltage at room temperature.
- Area: Occupies a small active area of 0.021 mm².
- Resolution: Exhibits a sensing resolution of 0.15 °C/LSB.
- Accuracy: Achieves a sensing accuracy of -0.7/0.6 °C over the temperature range of -30 °C to 70 °C after a single-point calibration at 30 °C.
- Linearity: Demonstrates good linearity across the measured temperature range and is robust to variations in input RF power levels (from 5 dBm to 12 dBm).
- Process Variation Immunity: The design shows good linearity and accuracy across different process corners (±4.5% variation in PTAT current).
Limitations and Future Work
- Resolution Improvement: The authors acknowledge that improving the resolution is a target for future work.
- Input RF Power Sensitivity: While the sensor shows good immunity to supply voltage variations, its performance can be affected by input RF power levels. Low input power (≤5 dBm) may not be sufficient to activate the tag, leading to errors, and excessively high power (≥12 dBm) can cause overheating due to the internal power limiter. The optimal range is identified as 5-12 dBm.
- Calibration: While only 1-point calibration is required, which is a significant advantage, further reducing or eliminating the need for calibration would be ideal.
The authors plan to focus on improving the resolution in future designs.
Summary updated