DESIGN OF A KU BAND SIX BIT PHASE SHIFTER USING PERIODICALLY LOADED-LINE AND SWITCHED-LINE WITH LOADED-LINE

Zhigang Wang, Bo Yan, Ruimin Xu, Yunnchuan GuoElectromagnetic 2007 · DOI

Abstract

A Ku band six-bit phase shifter is presented in this work. The developed phase shifter consists of four bits realized as periodically loaded-line and two bits based on novel switched-line with loaded-line. A 71 $\Omega$ line impedance is chosen for the main transmission line in order to reduce the diode loss. Every bit has special tuning elements for the fine tuning of the required phase shift. The phase error for the 64 phase states is not greater than 3.4 degrees at the designed center frequency of 15 GHz, and the insertion loss for the 64 phase states is 5.2 dB $\pm$ 1.1 dB over the operating bandwidth of 14.9-15.1 GHz.

Introduction: The Role of Phase Shifters in Phased Arrays

Phase shifters serve as the critical "steering wheel" for phased array antenna systems, enabling electronic beamforming in applications ranging from satellite communications to advanced radar. While various technologies like MEMS or FETs offer specific advantages, PIN diode-based shifters remain a popular choice due to their commercial availability and ease of fabrication. However, traditional designs often struggle with significant phase errors and limited post-fabrication tunability. This research addresses these challenges by proposing a high-precision, six-bit digital phase shifter for the Ku-band (15 GHz) that achieves remarkably low phase error through a hybrid architectural approach.

Design Methodology: A Hybrid Approach

To achieve 64 distinct phase states, the authors developed a six-bit cascaded structure consisting of 5.625°, 11.25°, 22.5°, 45°, 90°, and 180° bits. The design leverages two distinct topologies optimized for different phase shift magnitudes:

  1. Small Bits (5.625° to 45°): These utilize a periodically loaded-line structure. The phase shift is precisely determined by the length of open-ended stubs branching off the main transmission line.
  2. Large Bits (90° and 180°): These employ a novel switched-line with loaded-line configuration. By integrating tuning stubs into traditional switched paths, the design compensates for the reactive elements of the PIN diodes, which typically introduce errors at high frequencies.
Schematic layout of the six-bit phase shifter showing the cascaded bits and tuning elements.

Furthermore, the team optimized the internal impedance of the circuit. Instead of the standard 50 $\Omega$ line, a 71 $\Omega$ main transmission line was selected. This higher impedance increases the ratio between the line impedance and the diode's series resistance, effectively reducing insertion loss across the six cascaded bits. $\lambda/4$ transformers are used at the input and output to interface with standard 50 $\Omega$ systems.

Key Innovations: Tuning and Loss Mitigation

A standout feature of this design is the inclusion of specific tuning elements within the phase shifter bits. In conventional RF designs, manufacturing tolerances or diode parasitics often necessitate a complete redesign if the phase shift is inaccurate. Here, the phase shift can be "dialed in" by slightly adjusting the lengths of these branches during the design and simulation phase.

The hybrid topology ensures that each bit is handled by the structure best suited for its magnitude—periodically loaded lines for small, stable shifts and modified switched-lines for the larger 90° and 180° shifts. This strategic combination optimizes both the physical footprint and the electrical performance.

Experimental Results

The fabricated prototype was evaluated over an operating range of 14.9–15.1 GHz. The results demonstrate high precision and competitive performance for a PIN diode-based system:

  • Phase Precision: The maximum phase error across all 64 states was recorded at just 3.4 degrees at the 15 GHz center frequency.
  • Insertion Loss: The measured loss was 5.2 dB $\pm$ 1.1 dB. While seemingly high, this is competitive for a six-bit PIN diode shifter at Ku-band frequencies.
  • Impedance Matching: The Voltage Standing Wave Ratio (VSWR) remained below 1.92 for all states, indicating efficient signal transmission.
  • Individual Bit Performance: The 5.625° bit showed a phase error of less than $\pm$1.1°, while the 180° bit remained within $\pm$1.35°.
Performance of the phase shifter (c) and a photograph of the fabricated prototype in its housing (d).

Conclusion and Future Directions

The proposed hybrid architecture successfully delivers a high-precision Ku-band phase shifter with manageable insertion loss and excellent phase accuracy. The primary limitation of the current design is its narrow fractional bandwidth of approximately 1.3% (14.9–15.1 GHz). Future research could focus on adapting this hybrid approach for wideband applications or exploring automated tuning methods to streamline mass production.

Summary updated

Abstract

A Ku band six-bit phase shifter is presented in this work. The developed phase shifter consists of four bits realized as periodically loaded-line and two bits based on novel switched-line with loaded-line. A 71 line impedance is chosen for the main transmission line in order to reduce the diode loss. Every bit has special tuning elements for the fine tuning of the required phase shift. The phase error for the 64 phase states is not greater than 3.4 degrees at the designed center frequency of 15 GHz, and the insertion loss for the 64 phase states is 5.2 dB1.1 dB over the operating bandwidth of 14.9-15.1 GHz.
BibTeX
@inproceedings{wang2007design,
  author = {Zhigang Wang and Bo Yan and Ruimin Xu and Yunnchuan Guo},
  title = {{DESIGN OF A KU BAND SIX BIT PHASE SHIFTER USING PERIODICALLY LOADED-LINE AND SWITCHED-LINE WITH LOADED-LINE}},
  booktitle = {Electromagnetic},
  year = {2007},
  doi = {10.2528/pier07071904},
}
Figure