Design of a Humidity Sensor Tag for Passive Wireless Applications

Xiang Wu, Fangming Deng, Yong Hao, Zhihui Fu, Lihua ZhangSensors 2015 · DOI

TL;DR

This paper presents a novel, low-cost, and ultra-low-power wireless humidity sensor tag fabricated using standard CMOS technology. It integrates a capacitive humidity sensor with an RFID transceiver, enabling battery-less operation and achieving a significant communication range of 23 meters.

What Problem Does This Paper Address?

Accurate and widespread humidity measurement is crucial across various fields, from meteorology to industrial control. While capacitive humidity sensors offer advantages in terms of power consumption and interface complexity, integrating them into wireless systems, especially for low-cost applications, presents challenges. Existing solutions often require complex post-processing steps, specialized fabrication techniques, or operate at frequencies limiting their range and speed. This paper aims to bridge this gap by developing a fully integrated, passive UHF RFID humidity sensor tag that is cost-effective and achieves a substantial wireless communication range.

Methods

The core of this work lies in the integrated design of a humidity sensor and its associated RFID circuitry within a standard 0.18 µm CMOS process.

  • Humidity Sensor: A capacitive sensor is implemented using interdigitated top metal electrodes, with the gaps filled by a humidity-sensitive polyimide layer. This approach leverages standard CMOS fabrication without post-processing, reducing cost and complexity.
  • RFID Transceiver: The tag utilizes a passive UHF RFID architecture.
  • Rectifier: A two-stage rectifier with a dynamic bias-voltage generator is employed. This design aims to achieve a flat power conversion efficiency curve across a wider range of input power, crucial for maximizing the communication distance.
  • Sensor Interface: A phase-locked loop (PLL)-based architecture is used for capacitance-to-digital conversion. This fully digital interface is designed to operate at an ultra-low supply voltage (0.5 V), further reducing power consumption and enhancing immunity to supply variations.
  • Modulator: An Amplitude Shift Keying (ASK) backscattering modulation scheme is used for wireless communication.

Datasets

Not discussed in the paper. The performance evaluation relies on measurements conducted in a controlled laboratory environment using a humidity chamber and specialized RFID test equipment.

Key Insights and Ideas

  • CMOS Integration for Cost Reduction: Fabricating the entire humidity sensor tag, including the sensing element and RFID circuitry, in a standard CMOS process without post-processing is a key enabler for low-cost applications.
  • Dynamic Bias for Rectifier Efficiency: The dynamic bias-voltage generator in the rectifier is crucial for maintaining high power conversion efficiency over a broader input power range, directly impacting the tag's operating distance.
  • PLL-Based Interface for Low Power: The fully digital PLL-based sensor interface allows for ultra-low voltage operation (0.5 V) and inherent immunity to supply variations, significantly reducing power consumption compared to analog-based interfaces.
  • UHF Frequency for Extended Range: Operating at the UHF band (900 MHz) is essential for achieving the desired long-range wireless communication.

Key Results

  • Excellent Linearity, Hysteresis, and Stability: The humidity sensor exhibits highly linear performance (10% to 90% RH), with hysteresis not exceeding 8% at 55% RH, and excellent stability over 45 hours of testing.
  • Sensitivity: The sensor achieves a sensitivity of 18.75 fF/%RH at 25 °C.
  • Response Time: The sensor has a response time of 20 seconds to reach 90% of the steady state.
  • Ultra-Low Power Consumption: The total power dissipation of the sensor tag is remarkably low at 2.5 µW.
  • Extended Communication Range: Under a 4 W RFID reader power, the tag achieves a maximum operating distance of 23 meters.
  • Rectifier Performance: The proposed rectifier achieves a peak power conversion efficiency of 69% and provides a higher output voltage (0.6 V at -20 dBm input) compared to conventional designs.
  • Sensor Interface Performance: The interface operates at 0.5 V with a low FOM of 1.6 pJ/conversion and a power consumption of 1.1 µW.

Limitations and Future Work

  • Moderate ENOB: The paper acknowledges a moderate Effective Number of Bits (ENOB) for the sensor interface.
  • Temperature Dependence: While the average duty cycle shows an acceptable maximum temperature variation of 10% from 0 to 60 °C, further investigation into mitigating temperature effects on sensor performance might be beneficial.
  • Future Work: The authors suggest that this integrated approach is highly suitable for passive RFID applications, implying potential for further optimization and broader adoption in various IoT scenarios. The integration of other sensing modalities could also be a future direction.

Summary updated

BibTeX
@article{wu2015design,
  author = {Xiang Wu and Fangming Deng and Yong Hao and Zhihui Fu and Lihua Zhang},
  title = {{Design of a Humidity Sensor Tag for Passive Wireless Applications}},
  journal = {Sensors},
  year = {2015},
  doi = {10.3390/s151025564},
}
Figure