Design, Fabrication and Experimental Validation of a Novel Dry-Contact Sensor for Measuring Electroencephalography Signals without Skin Preparation

Lun‐De Liao, I-Jan Wang, Sheng-Fu Chen, Jyh‐Yeong Chang, Chin‐Teng LinSensors 2011 · DOI

TL;DR

This paper introduces a novel dry-contact EEG sensor designed for user comfort and convenience, eliminating the need for skin preparation or conductive gels. The sensor utilizes a flexible substrate with 17 spring-loaded probes, allowing for excellent scalp conformity and stable signal acquisition, even on hairy sites, achieving comparable performance to traditional wet electrodes.

What Problem Does This Paper Address?

Traditional Electroencephalography (EEG) signal acquisition relies heavily on wet electrodes, which, while effective, necessitate a cumbersome and often uncomfortable multi-step process. This includes skin preparation (like abrasion) and the application of conductive gels to reduce skin-sensor interface impedance. These procedures are time-consuming, can cause skin irritation or infection, and are particularly inconvenient for long-term monitoring or daily use. Furthermore, hair can significantly impede proper contact, degrading signal quality. The paper aims to overcome these limitations by developing a dry-contact sensor that offers comparable or better performance without any of these drawbacks.

Methods

The core innovation lies in the sensor's design and fabrication. The researchers developed a dry-contact EEG sensor featuring a flexible substrate embedded with 17 individual spring-loaded contact probes. Each probe consists of a gold-coated probe head, a beryllium copper plunger, a spring, and a barrel. This design allows the probes to conform to the irregular scalp surface, maintaining consistent contact and low impedance. The entire sensor is fabricated using an injection molding process, which is described as a one-time forming process for the flexible substrate with integrated probes. This manufacturing method is highlighted for its potential for mass production and cost reduction. The paper also details the design of a wireless EEG acquisition module, including a biosignal amplifier, acquisition component, microprocessor, and wireless transmission component, used to collect and transmit the EEG data.

Datasets

Not discussed in the paper. The experiments involved human subjects for impedance measurements and EEG signal acquisition.

Key Insights and Ideas

  • Scalp Conformity is Key: The flexible substrate and spring-loaded probes are crucial for achieving good contact and low impedance on the irregular scalp surface, even in the presence of hair. This addresses a major challenge for dry electrodes.
  • Buffering for Comfort: The spring mechanism not only ensures contact but also acts as a buffer, preventing pain or discomfort when force is applied to the sensor.
  • Injection Molding for Scalability: The use of injection molding for fabrication is a significant advantage, suggesting that these sensors can be manufactured cost-effectively at scale, paving the way for wider adoption.
  • Hair is No Longer a Major Barrier: The design demonstrates effective EEG acquisition on hairy sites, a significant improvement over many existing dry electrode technologies.
  • Simplicity Drives Adoption: Eliminating skin preparation and conductive gels dramatically simplifies the EEG setup, making it more accessible for everyday use and long-term monitoring.

Key Results

  • Impedance Performance: The dry EEG sensor achieved impedance values comparable to, and in some cases lower than, wet electrodes, even on hairy sites. Specifically, impedance variation for the dry sensor was in the range of 4 to 14 kΩ, considered acceptable for normal EEG measurements.
  • Long-Term Stability: Long-term impedance measurements (3 hours) showed significantly less variation for the dry EEG sensor compared to conventional wet electrodes, attributed to the absence of drying conductive gels.
  • High Signal Correlation: EEG signal quality was evaluated by comparing signals from the dry sensor to prerecorded EEG data. The average correlation was found to be very high, approximately 98.14%.
  • Comparable Performance to Wet Electrodes: Signal quality comparisons between the dry sensor and wet electrodes (with skin preparation) showed high correlations: 95.26% on the forehead and 91.47% on a hairy site. EOG and eye-blink signal correlations were also significant (89.26% and 88.84%, respectively).

Limitations and Future Work

  • Limited Dataset: The study involved a relatively small number of subjects for impedance measurements (five) and long-term impedance variation (six).
  • Specific Sites Tested: While hairy sites were tested, the full range of hair densities and types was not exhaustively explored.
  • Future Work: The authors suggest that these dry EEG sensors are ideally suited for future monitoring of human EEG states, particularly for brain-computer interface (BCI) applications, due to their ease of use and stability. Further research could explore optimizing the probe design for even greater comfort and signal quality across diverse populations and hair conditions.

Summary updated

Abstract

In the present study, novel dry-contact sensors for measuring electro-encephalography (EEG) signals without any skin preparation are designed, fabricated by an injection molding manufacturing process and experimentally validated. Conventional wet electrodes are commonly used to measure EEG signals; they provide excellent EEG signals subject to proper skin preparation and conductive gel application. However, a series of skin preparation procedures for applying the wet electrodes is always required and usually creates trouble for users. To overcome these drawbacks, novel dry-contact EEG sensors were proposed for potential operation in the presence or absence of hair and without any skin preparation or conductive gel usage. The dry EEG sensors were designed to contact the scalp surface with 17 spring contact probes. Each probe was designed to include a probe head, plunger, spring, and barrel. The 17 probes were inserted into a flexible substrate using a one-time forming process via an established injection molding procedure. With these 17 spring contact probes, the flexible substrate allows for high geometric conformity between the sensor and the irregular scalp surface to maintain low skin-sensor interface impedance. Additionally, the flexible substrate also initiates a sensor buffer effect, eliminating pain when force is applied. The proposed dry EEG sensor was reliable in measuring EEG signals without any skin preparation or conductive gel usage, as compared with the conventional wet electrodes.
BibTeX
@inproceedings{liao2011design,
  author = {Lun‐De Liao and I-Jan Wang and Sheng-Fu Chen and Jyh‐Yeong Chang and Chin‐Teng Lin},
  title = {{Design, Fabrication and Experimental Validation of a Novel Dry-Contact Sensor for Measuring Electroencephalography Signals without Skin Preparation}},
  booktitle = {Sensors},
  year = {2011},
  doi = {10.3390/s110605819},
}
Figure