Design And Implementation Of A Probe Station As Capstone Project

Licheng Jiao, Jeffrey Ray2020 · DOI

Abstract

A probe station is an essential piece of equipment used in semiconductor wafer testing. It provides a platform for the wafer to interface with the electrical test equipment. During wafer testing, electrical probes are lowered onto the semiconductor wafer and make electrical connections to the wafer. This paper presents the design and implementation of a probe station project that was carried out as a capstone senior design project in the School of Engineering at Grand Valley State University. The probe station was designed to have a durable, stable base and a 4-inch vacuum-assisted hot chuck as a sample stage. A microscope was integrated to view the wafers and to assist in making the electrical connections. In addition, microprobes with the ability to probe wafers of 25µm structure were designed. The project team consisted of students with majors in mechanical and electrical engineering. The outcome of this project was a fully functional probe station currently used in the solid-state laboratory.

Introduction

In the world of semiconductor fabrication, "probing" is a critical bottleneck. To test integrated circuits before they are packaged, researchers must physically touch microscopic pads on a silicon wafer with electrical needles. Commercial probe stations that offer the necessary stability, precision, and thermal control are notoriously expensive, often costing tens of thousands of dollars. For many university engineering programs, this price tag is a barrier to providing students with hands-on experience. This project details how a multidisciplinary team of senior students bridged this gap by designing a custom station that meets professional specifications while adhering to a strict $3,000 budget.

Design and Methodology

The project followed a two-course capstone sequence (EGR 485/486) emphasizing real-world project management. The team, comprising four mechanical and two electrical engineering students, utilized several key engineering techniques to achieve high-precision results.

Figure 1: Overview of the completed probe station assembly showing major components including the microscope, micromanipulators, and sample stage.

Mechanical and Thermal Systems

To ensure the "hot chuck" (the platform holding the wafer) maintained a uniform temperature, the team used a numerical mesh method to solve the energy equation. They compared band heaters versus disc heaters, ultimately selecting a disc heater for its superior thermal uniformity. The chuck was fabricated from low-carbon steel and gold-plated to ensure high electrical conductivity.

Figure 5: Detailed view of the chuck assembly, highlighting the disc heater, ceramic insulation, and the XY-Z positioning stages.

A vacuum-assisted system was designed to securely hold 4-inch wafers in place during testing. For precision positioning, the team integrated a commercially available XY table with a custom-built "scissor jack" Z-axis. For the microprobes, they designed micromanipulators using aluminum sliding blocks and threaded rods to achieve sub-micron precision.

Key Results

The project met or exceeded all design requirements:

  • Precision: Achieved a micromanipulator resolution of 50nm, verified using a test wafer with 50nm-spaced lines.
  • Thermal Performance: The chuck reached 300°C with a maximum temperature variance of only 5°C between the center and the edge. This was a significant improvement over band heater designs, which showed drops down to 112.5°C at the center.
  • Electrical Integrity: The resistance from the BNC connector to the probe tip was measured at less than 2 ohms, ensuring clean signal transmission.
  • Cost Efficiency: The final project cost was **$2,985**, successfully meeting the $3,000 budget constraint.

Conclusion

The project demonstrates that by strategically combining off-the-shelf components with custom-machined parts, universities can create high-end lab equipment at a 90% discount. While the current system is manual, it provides a robust platform for future automation or environmental shielding upgrades. The station is now a permanent fixture in GVSU’s solid-state laboratory, providing a platform for students to study the functional properties of integrated circuits in wafer form.

Summary updated

Abstract

A probe station is an essential piece of equipment used in semiconductor wafer testing. It provides a platform for the wafer to interface with the electrical test equipment. During wafer testing, electrical probes are lowered onto the semiconductor wafer and make electrical connections to the wafer. This paper presents the design and implementation of a probe station project that was carried out as a capstone senior design project in School of Engineering at Grand Valley State University. The probe station was designed to have a durable, stable base and a 4 inch vacuum-assisted hot chuck as a sample stage. A microscope was integrated to view the wafers and to assist in making the electrical connections. In addition, microprobes with the ability to probe the wafers of 25om structure were designed. The project team consisted of students with majors in mechanical and electrical engineering. The students learned skills in team building, project management, communication skills, and budgeting. The outcome of this project was a fully functional probe station currently used in the solid-state laboratory.
BibTeX
@misc{jiao2020design,
  author = {Licheng Jiao and Jeffrey Ray},
  title = {{Design And Implementation Of A Probe Station As Capstone Project}},
  year = {2020},
  doi = {10.18260/1-2--521},
}
Figure