Crystal plasticity finite element modelling of coarse-grained <mml:math xmlns:mml="http://www.w3.org/1998/Math/MathML" altimg="si98.svg"><mml:mrow><mml:mi>α</mml:mi></mml:mrow></mml:math>-uranium

Nicolò Grilli, A.c.f. Cocks, Edmund TarletonComputational 2019 · DOI

TL;DR

This paper presents a crystal plasticity finite element model (CPFEM) for coarse-grained α-uranium, crucial for understanding its manufacturing and fracture behavior. The model accurately captures experimental stress-strain curves and lattice strains by incorporating thermal residual stresses from manufacturing and calibrating material parameters, revealing a strong grain size dependence for twinning.

What Problem Does This Paper Address?

Understanding the mechanical behavior of α-uranium is critical for its safe manufacturing and predicting potential fracture. α-uranium has a complex, anisotropic crystal structure, leading to significant internal stresses during manufacturing processes like quenching. These residual stresses, combined with the material's inherent plasticity mechanisms (slip and twinning), dictate its macroscopic response. Previous modeling efforts primarily focused on fine-grained α-uranium, leaving a gap in understanding the behavior of coarse-grained material, which is relevant for cast components and weld zones. Specifically, the paper aims to:

  • Develop and validate a CPFEM model for coarse-grained α-uranium.
  • Incorporate the effects of manufacturing-induced thermal residual stresses.
  • Quantify the activity of slip and twin systems and their critical resolved shear stresses (CRSS).
  • Investigate the influence of grain size on the deformation mechanisms.

Methods

The authors employ a crystal plasticity finite element method (CPFEM) framework to simulate the deformation of α-uranium. Key methodological aspects include:

  • Constitutive Model: The model incorporates 8 slip systems and 2 twin systems, with dislocation densities serving as state variables.
  • Manufacturing Simulation: The simulation begins by modeling the manufacturing process: a quenching stage from 400°C to room temperature, followed by cutting a sub-volume to allow for the relaxation of internal stresses. This captures the crucial thermal residual stresses.
  • Material Parameter Calibration: Model parameters, particularly the CRSS for slip and twinning, are calibrated by comparing simulated stress-strain curves and lattice strains against experimental data from in situ neutron diffraction and tensile/compressive tests.
  • Dislocation Density Evolution: A multiplication-annihilation model for dislocation densities is used to capture hardening behavior.
  • Thermal Effects: The model accounts for the temperature dependence of the CRSS and the elastic constants.
  • Polycrystal Representation: A representative volume containing 8000 cubic grains (300 µm average size) is used to capture the polycrystalline nature and texture effects.

Datasets

  • Experimental Data: The study relies on experimental data from:
  • In situ neutron diffraction experiments to measure lattice strains.
  • Tensile and compressive stress-strain curves.
  • Electron backscatter diffraction (EBSD) images for twin volume fraction.
  • Texture Data: Experimental probability distribution functions for grain orientations (textures T1 for tension and C1 for compression) are used to orient the grains in the simulated polycrystal.

Key Insights and Ideas

  • Manufacturing Matters: Thermal residual stresses introduced during quenching significantly influence the subsequent mechanical behavior and plastic activity of coarse-grained α-uranium.
  • Grain Size Dependence is Strong for Twinning: The CRSS for {130} twinning in coarse-grained α-uranium is found to be similar to single crystals, but significantly lower than in fine-grained materials. This highlights a strong Hall-Petch effect for twinning.
  • Slip vs. Twinning: The relative activity of slip and twin systems is highly dependent on grain orientation and applied stress state (tension vs. compression), explaining observed tension-compression asymmetries.
  • CPFEM is Essential for Interpreting Neutron Diffraction: The study demonstrates that CPFEM is crucial for accurately interpreting neutron diffraction data, as it can account for the complex interplay of grain orientations, plastic deformation, and texture.
  • Model Validation: The developed CPFEM model successfully reproduces experimental stress-strain curves and elastic lattice strains for both tension and compression tests, validating its predictive capabilities.

Key Results

  • The CPFEM model accurately predicts stress-strain curves for both tension (T1 texture) and compression (C1 texture) samples, matching experimental data.
  • Simulated elastic lattice strains, averaged over specific grain families, show good agreement with neutron diffraction measurements, capturing subtle changes in slope indicative of plastic deformation.
  • The model predicts a {130} twin volume fraction of 5-6% after quenching in the central grains, which is consistent with experimental observations for coarse-grained material.
  • The CRSS for {130} twinning is estimated to be around 25 MPa, similar to single crystal values, while slip CRSS values are comparable to those for fine-grained uranium (25 µm grain size).

Limitations and Future Work

  • Discrepancy in Lattice Strain: While generally good, some discrepancies exist in the elastic lattice strain predictions, particularly for the compression sample's (100) plane. The authors suggest this could be due to strain concentrations outside the neutron beam's sampling region or an overestimation of twin CRSS if direct experimental analysis is performed without CPFEM.
  • Future Work: The authors suggest that this model is a first step towards understanding how fracture is affected by plastic deformation and texture in coarse-grained α-uranium. Further work could explore the link between the predicted plastic deformation and fracture mechanisms. The model could also be extended to investigate other deformation modes or higher temperatures.

Summary updated

Abstract

The deformation behaviour of coarse-grained α-uranium is studied using crystal plasticity finite element simulations. The constitutive model includes 8 slip and 2 twin systems, based on dislocation densities as state variables. Polycrystal simulations are carried out to reproduce the manufacturing procedure: a quenching stage is followed by cutting out a sub volume to allow relaxation of the internal stresses. Room temperature tension and compression experiments are simulated for the textured samples that are generated by this process. Calibration of the model parameters is obtained by comparing simulated experiments against measured stress-strain curves and lattice strains from published in situ neutron diffraction studies. The comparison of the internal elastic strains allows the activity of slip and twin modes to be quantified, and to estimate their critical resolved shear stresses. The comparison between the present simulation results and previous models for fine-grained α-uranium provides information about the grain size dependence of the strength of slip and twin systems. The critical resolved shear stress of the most prominent twinning mode {1 3 0} is found to be similar to single crystal samples and much smaller than for fine-grained samples, showing the strong grain size dependence of this deformation mode.
BibTeX
@inproceedings{grilli2019crystal,
  author = {Nicolò Grilli and A.C.F. Cocks and Edmund Tarleton},
  title = {{Crystal plasticity finite element modelling of coarse-grained <mml:math xmlns:mml="http://www.w3.org/1998/Math/MathML" altimg="si98.svg"><mml:mrow><mml:mi>α</mml:mi></mml:mrow></mml:math>-uranium}},
  booktitle = {Computational},
  year = {2019},
  doi = {10.1016/j.commatsci.2019.109276},
}
Figure