Conceptual full-vehicle modeling of a modular all-wheel-drive robotic ADS test platform as a foundation for a digital twin architecture

Felix Florian Schwald, Martin Meiners, Michael Viehof, Erik Hultman, Edwin KamauarXiv 2026 · arXiv

This paper details the creation of a foundational simulation model for the PixKit, a modular electric "skateboard" chassis designed for autonomous driving research. By integrating unconventional features like four-wheel independent drive and rear-axle steering into the IPG CarMaker environment, the authors provide a crucial "first layer" for future digital twin architectures.

TL;DR

Researchers developed a physics-based, extendable simulation model for the PixKit modular robotic platform in IPG CarMaker. This model serves as a traceable foundation for testing automated driving systems (ADS) and advanced vehicle dynamics, even before full physical measurement data is available.

What Problem Does This Paper Address?

In the world of autonomous vehicle development, "Digital Twins"—virtual replicas of physical systems—are essential for safe, rapid testing. However, modular research platforms like the PixKit often lack ready-to-use, high-fidelity simulation models.

The challenge is a "chicken and egg" problem: you need a model to develop control software, but you need the physical vehicle to gather the precise data (like suspension kinematics or motor efficiency maps) required for a high-fidelity model. This paper bridges that gap by building a "physically plausible" model based on manufacturer documentation and engineering assumptions, providing a functional sandbox for researchers to start their work.

Methods

The authors utilized IPG CarMaker, a standard industry tool for vehicle dynamics simulation. Key aspects of their modeling approach include:

  • System-Level Integration: Instead of a complex multibody reconstruction, they focused on the interaction between major subsystems: powertrain, suspension, steering, tires, and brakes.
  • Hybrid Parameterization: Since complete measurement data was missing, they combined documented specs (like wheelbase and mass) with derived values and "placeholders" (like linear spring rates) to ensure stability.
  • Unconventional Architecture: The model accounts for the high unsprung mass of four in-wheel hub motors and implements a selectable rear-axle steering (RAS) system.
  • Simulink Co-simulation: The RAS logic was integrated via a MATLAB/Simulink interface, allowing for complex steering strategies (like crab steering or counter-phase steering) to be added later.
The PixKit skateboard chassis dimensions used for the model's geometric foundation.

Datasets

The study did not use standard external datasets. Instead, it relied on:

  • PixKit Manufacturer Documentation: Provided primary geometric and powertrain data (e.g., 420 kg curb mass, 1900 mm wheelbase).
  • IPG CarMaker Presets: Used for standard components like tires (RT_225_45_R17) where specific PixKit data was unavailable.
  • Custom Parameter Set: A detailed list of all assumptions and derived values was compiled to ensure the model's traceability (see Table I in the paper).

Key Insights and Ideas

  • The "Enabling Layer": A model doesn't have to be 100% validated to be useful. A "traceable and functional" model allows for early-stage decision-making and software development while the physical vehicle is still being characterized.
  • Mass Distribution Matters: In-wheel motors significantly shift the vehicle's mass toward the wheels. The authors accounted for this by modeling each wheel assembly at 30 kg, which is critical for accurate vertical dynamics.
  • Visual Plausibility: Beyond the math, the authors used a custom Python script in the MovieNX visualizer to overlay real-time steering angles, helping researchers verify that the complex four-wheel steering logic was behaving correctly.
Figure 2. Top and side view of the PixKit visualization.

Key Results

The model was put through three primary "plausibility" tests:

  1. Straight-Line Acceleration: The vehicle reached a top speed of ~68 km/h, with a peak power output of 11 kW—very close to the documented 12 kW rated power of the four motors combined.
  2. Turning Circle: Activating counter-phase rear-axle steering reduced the simulated turning circle diameter from 8.2 m to 4.5 m (a ~45% reduction), matching the expected qualitative behavior of the physical platform.
  3. Stability: In steady-state circular driving at 20 km/h, the model showed bounded roll and slip behavior, confirming that the "placeholder" suspension and tire parameters provided a stable simulation environment.
Figure 5. Powertrain response during the straight-line maneuver.

Limitations and Future Work

The authors are clear that this is a conceptual model, not a fully validated digital twin.

  • Missing Data: The suspension uses linear approximations rather than measured non-linear characteristics. Motor and inverter thermal effects are also neglected.
  • Validation Gap: The model has not yet been calibrated against real-world sensor data from the physical PixKit.
  • Next Steps: Future work will focus on "closing the loop" by using real driving maneuvers to calibrate the model's parameters and integrating more advanced, speed-dependent steering controllers.

Summary updated

Abstract

This paper presents the development of an initial full-vehicle simulation model of the PixKit modular electric test platform in IPG CarMaker. The objective is to create a physics-based and extendable model structure that can serve as a low-level foundation for future digital twin applications. The reference vehicle is a skateboard chassis combining unconventional vehicle characteristics such as four independent wheel-hub motors and rear axle steering capable of high steering angles. Since complete measurement data of the vehicle is not yet available, the model parameterization is based on a combination of manufacturer documentation, derived values and engineering assumptions. The modeling approach focuses on the system-level integration of the main vehicle subsystems rather than on a fully validated representation. The resulting model was assessed through basic driving scenarios with different steering inputs and configurations. The simulations showed stable model behavior and physically plausible interaction between the subsystems. The all-wheel-drive configuration produced symmetric wheel responses in longitudinal driving, while counter-phase rear axle steering increased the yaw response and reduced the simulated turning circle diameter compared with front axle steering only. The circular driving scenario further indicated bounded roll and slip behavior. Overall, the implemented CarMaker model provides a traceable and functional simulation basis for the PixKit vehicle. It can support future model refinement, calibration with real vehicle data and development with the goal of creating a validated digital twin architecture.
BibTeX
@misc{schwald2026conceptual,
  author = {Felix Florian Schwald and Martin Meiners and Michael Viehof and Erik Hultman and Edwin Kamau},
  title = {{Conceptual full-vehicle modeling of a modular all-wheel-drive robotic ADS test platform as a foundation for a digital twin architecture}},
  year = {2026},
  eprint = {2611.24646},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/2611.24646},
}

Loading related content...

Figure