Compressed Sensing-based Blind Reconstruction of Multi-frequency Blade Vibration from Under-sampled BTT Signals

Hailong Xu, Yang Yon, Haifeng Hu, Guan Fengjiao, Zhongsheng ChenJournal of Mechanical Engineering 2019 · DOI

Abstract: Rotating blades are core components of aeroengines, operating under complex conditions where alternating stresses can lead to vibration-induced fatigue failure. Online vibration monitoring is essential for operational safety. Traditional contact-based strain gauge methods are limited by complex wiring and the inability to monitor all blades simultaneously. This paper explores Blade Tip-Timing (BTT) as a non-contact alternative. However, BTT signals are typically under-sampled due to physical sensor placement constraints, making the reconstruction of multi-frequency vibrations challenging. We propose a Compressed Sensing (CS) approach combined with the Multiple Signal Classification (MUSIC) algorithm for the blind reconstruction of these vibrations. Numerical simulations and experimental tests demonstrate that this method effectively identifies vibration frequencies and reconstructs waveforms from sparse BTT data.

Introduction

The health of aeroengine blades is paramount for flight safety. Fatigue failure caused by vibration is a primary concern in engine maintenance. While Blade Tip-Timing (BTT) has emerged as a powerful non-contact monitoring tool, its low sampling rate—often far below the Nyquist-Shannon limit—leads to significant aliasing. Real-world blade vibrations are often "multi-frequency" due to aerodynamic excitation or structural defects, further complicating signal recovery without prior knowledge of the vibration characteristics.

Methodology

The proposed framework treats blade vibration as a sparse signal in the frequency domain. By establishing a dynamic mechanical model, the researchers demonstrated that vibrations under aerodynamic loads consist of a few dominant frequencies rather than a continuous spectrum. The BTT measurement process is modeled as a Compressed Sensing problem ($Y = \Phi X$), where $Y$ represents the under-sampled sensor data and $X$ is the unknown sparse frequency spectrum.

Schematic of the BTT experimental setup and sensor arrangement.

To solve this under-determined system, the Multiple Signal Classification (MUSIC) algorithm is employed. Typically used in radar and direction-finding, MUSIC is adapted here to identify the specific "support" (the active vibration frequencies) from very limited data. Once the frequencies are identified, the actual vibration amplitudes are reconstructed using a pseudo-inverse matrix approach, allowing for "blind" reconstruction without pre-existing frequency data.

Key Results

The method was validated using a high-speed rotating blade test rig. In experimental tests at a rotational speed of 1520 r/min, the system successfully identified the fundamental vibration frequency at 25.46 Hz and its second harmonic at 50.79 Hz using only three BTT sensors. Traditionally, achieving such resolution would require dozens of sensors to satisfy the Nyquist criterion.

Reconstructed time-domain vibration curve and the corresponding displacement frequency spectrum.

As shown in the results, the reconstructed time-domain waveform aligns well with the expected periodic behavior, and the displacement spectrum clearly distinguishes the primary vibration components. This demonstrates the ability to break the Nyquist barrier, achieving high-resolution monitoring with a fraction of the hardware required by traditional theory. The reconstructed waveforms closely matched simulated "true" vibrations, with only minor differences in peak amplitudes caused by measurement noise.

Conclusion

By leveraging the inherent sparsity of blade vibrations, Compressed Sensing and the MUSIC algorithm enable the blind reconstruction of multi-frequency signals from under-sampled BTT data. This approach significantly reduces the hardware requirements for aeroengine health monitoring while maintaining high diagnostic accuracy. Future work will focus on adapting the method for non-stationary signals during engine acceleration and deceleration phases to better reflect real-world flight conditions.

Summary updated

Abstract

摘要: 旋转叶片是航空发动机的核心部件,长期工作在复杂的工况下承受交变应力,容易产生振动而导致疲劳失效,因此在线监测叶片振动对发动机运行安全具有十分重要的工程意义。针对传统的接触式应变法无法同时测量所有叶片振动且布线复杂存在安全隐患的问题,采用叶端定时(Blade tip-timing,BTT)非接触方法对叶片振动进行实时在线监测。但是BTT测量信号受叶顶传感器安装限制属于典型的欠采样信号,而叶片由于气动激励及微小裂纹的非线性导致其叶端出现多频振动响应,因此利用欠采样的BTT信号获取未知多频叶片振动是目前遇到的巨大挑战。提出采用压缩感知方法解决BTT欠采样多频叶片振动盲重构。首先分析叶片在气动激励下的多频响应;然后建立BTT测量的压缩感知模型,并采用多重信号分类(Multiplesignal classification,MUSIC)算法进行求解;最后通过数值仿真,并结合旋转叶片BTT测振实验台验证了压缩感知理论解决BTT欠采样多频叶片振动盲重构难题,实现旋转叶片振动BTT非接触在线测量。
BibTeX
@article{xu2019compressed,
  author = {Hailong Xu and Yang Yon and Haifeng Hu and Guan Fengjiao and Zhongsheng Chen},
  title = {{Compressed Sensing-based Blind Reconstruction of Multi-frequency Blade Vibration from Under-sampled BTT Signals}},
  journal = {Journal of Mechanical Engineering},
  year = {2019},
  doi = {10.3901/jme.2019.13.113},
}
Figure