TL;DR
This paper investigates a pre-support technology for constructing new subway lines that pass under existing, aging subway lines. By combining field monitoring and advanced numerical simulations, the study demonstrates that this method significantly controls settlement and stress on the older infrastructure, ensuring operational safety and minimizing damage.
What Problem Does This Paper Address?
Urban areas are experiencing rapid growth, leading to increased demand for public transportation like subways. This often necessitates building new subway lines that must pass beneath or near existing, operational lines. Older subway systems, like Beijing's 50-year-old Line 2, are particularly vulnerable to the stresses and deformations caused by new construction. The challenge is to implement new infrastructure projects without compromising the safety, stability, and functionality of these critical, aging transit networks. Traditional construction methods can cause significant ground disturbance, leading to settlement and stress issues in existing structures. This paper addresses the need for a construction method that minimizes these negative impacts, specifically focusing on a "close-fitting undercrossing" scenario.
Methods
The research employs a multi-pronged approach:
- Field Monitoring: On-site measurements were taken on the existing Line 2 and the new Line 3 during the construction of the undercrossing. This involved both manual (gauge ruler, spirit level) and automated monitoring systems to track track gauge, crosslevel, and deformation of bearing columns and floor slabs.
- Numerical Simulation: A detailed three-dimensional finite difference model was created using FLAC3D software. This model incorporated the geological conditions, the existing subway structure (Line 2), and the new tunnel construction process. Material parameters were derived from geotechnical investigations and laboratory tests on concrete samples from the existing structure.
- Laboratory Tests: Uniaxial compression tests, elastic modulus, and Poisson's ratio tests were conducted on concrete samples from the existing subway structure to obtain accurate material parameters for the numerical model.
- Comparative Analysis: The proposed pre-support technology was compared against another common method, the cross diaphragm (CRD) method, through numerical simulations to highlight the advantages of the new approach.
Datasets
Not explicitly detailed as "datasets" in the traditional machine learning sense. The study relies on:
- Geological Survey Data: Provided parameters for various soil strata.
- Laboratory Test Results: Data from concrete testing of the existing subway structure.
- Field Monitoring Data: Measurements collected from the existing Line 2 and the construction site during the undercrossing project. This data was used for model calibration and validation.
Key Insights and Ideas
- Direct Contact Support is Crucial: The pre-support technology, utilizing bored piles and jacks, provides direct physical support to the existing structure. This is a key differentiator from methods that rely solely on ground improvement, which can lead to greater soil disturbance.
- Minimizing Time Gaps is Key: The study emphasizes the importance of minimizing the time intervals between construction steps (e.g., pile foundation construction and jack placement) to ensure a continuous and effective support system.
- Deformation Joints are Vulnerable Points: The research highlights that deformation joints in the existing structure are particularly susceptible to displacement during construction, requiring careful monitoring.
- Pre-support Technology Outperforms CRD: Numerical comparisons show that the pre-support method results in significantly less settlement and stress variation in the existing subway line compared to the CRD method.
Key Results
- Track Smoothness Maintained: The pre-support technology caused minimal impact on the smoothness of the existing subway rail surface, with fluctuations within -1 to 1 mm.
- Settlement Control: Settlement deformation of the existing lines was effectively controlled within 1-3 cm.
- Stress Within Limits: Deformation stress on existing lines remained within the concrete strength range, with tensile stress less than 3 MPa.
- Maximum Settlement: The pre-support jacking scheme resulted in a maximum settlement of -5.27 mm.
- Maximum Tensile Stress: The maximum tensile stress observed was 2.29 MPa.
- CRD Method Comparison: The CRD method resulted in a much larger maximum settlement of -61.28 mm and a maximum tensile stress of 2.47 MPa, indicating a greater impact on the existing structure.
Limitations and Future Work
- Scope of Monitoring: The numerical model focused on the influence of the underpass construction process itself. The paper acknowledges that the influence of other underground construction activities on the on-site displacement was not considered and suggests this as an area for further study.
- Geological Conditions: The study's findings are based on the specific geological conditions of the Beijing subway. While the method is presented as applicable to sandy cobble strata, further research might explore its performance in a wider range of geological environments.
- Optimization: The paper mentions that optimization measures were proposed based on monitoring data and simulation results, but these specific measures are not detailed in the provided text. Future work could elaborate on these optimizations.
Summary updated