Comprehensive Experimental Investigation of Operational Parameter Sensitivity in Proton Exchange Membrane Fuel Cell Performance

Renhua Feng, Zhanye Hua, Jing Yu, Shaoyang Wang, Lubing Shi, Xing Shu, Zeyu Yan, Jiayi GuoBatteries 2025 · DOI

TL;DR

This paper provides a comprehensive experimental analysis of how key operating parameters (excess gas coefficients, pressure, humidity, and coolant temperature) affect the performance of individual Proton Exchange Membrane Fuel Cells (PEMFCs). The findings highlight that while increasing certain parameters can improve voltage, there are optimal operating points, and complex interdependencies exist between parameters, crucial for efficient PEMFC design and control.

What Problem Does This Paper Address?

Proton Exchange Membrane Fuel Cells (PEMFCs) are a promising clean energy technology for transportation, offering high efficiency and zero emissions. However, their performance is highly sensitive to a multitude of operating conditions. While many studies have explored these sensitivities through modeling, there's a critical need for comprehensive experimental validation to understand the nuanced interactions and identify optimal operating windows. This paper addresses this gap by systematically investigating the impact of several key parameters on single PEMFC performance, aiming to provide practical insights for improving efficiency and durability.

Methods

The researchers conducted a series of experiments using a single PEMFC test setup. They systematically varied five key operating parameters:

  • Hydrogen and Air Excess Coefficients: Ratios of actual to stoichiometric reactant supply.
  • Cathode Inlet Pressure: The pressure of the air supplied to the cathode.
  • Intake Relative Humidity: The moisture content of the incoming gases.
  • Coolant Inlet Temperature: The temperature of the cooling fluid circulating through the cell.

They measured the fuel cell node voltage across a range of current densities (0 to 2.0 A/cm²) under controlled variations of these parameters. The experimental setup and parameters are detailed in Tables 1 and 2, and the specific operating points are outlined in Table 3 and Figure 2. The study focused on analyzing the voltage response to incremental changes in each parameter, often comparing deviations from a baseline condition.

Datasets

Not discussed in the paper. The study relies on experimental data generated from their specific PEMFC test setup.

Key Insights and Ideas

  • The "Sweet Spot" Principle: For most parameters, simply increasing them doesn't guarantee better performance. There's an optimal range, and exceeding it can lead to diminishing returns or even performance degradation. This is crucial for avoiding over-engineering and unnecessary energy consumption.
  • Current Density Matters: The impact of many parameters becomes more pronounced at higher current densities. This suggests that optimizing for peak performance might require different strategies than optimizing for low-load efficiency.
  • Interdependence is Key: The paper strongly emphasizes that parameters don't operate in isolation. Coolant temperature and humidity, for instance, have a "strong coupling relationship," meaning their combined effect is more than the sum of their individual impacts. This points to the need for holistic control strategies.
  • Excess Gas: A Double-Edged Sword: While increasing excess gas coefficients generally boosts voltage, excessively high values can increase compressor power consumption (a major energy drain in the auxiliary system) and potentially lead to other issues like flooding or dilution.
  • Pressure Optimization: Similar to excess gas, intake pressure has an optimal point. While higher pressure generally improves performance by increasing reactant concentration, it also necessitates more robust (and expensive) components and can lead to diminishing returns.

Key Results

  • Excess Coefficient: Increasing the excess coefficient generally increases cell voltage, with the effect becoming more significant at higher current densities (e.g., a 0.1 increment yields ~0.3 mV at 0.1 A/cm² but ~10 mV at 2.0 A/cm²). However, exceeding a certain threshold (around 2.5-2.6) offers no further benefit and increases auxiliary power demand.
  • Intake Pressure: A 5 kPa increase in intake pressure typically yields about a 2 mV voltage gain, which doubles to 4 mV at 2.0 A/cm². An optimal pressure range (around 150-170 kPa for air) is identified, aligning with industrial practices.
  • Coolant Temperature: At moderate current densities, voltage increases with coolant temperature. However, this trend reverses at high current densities (>2 A/cm²), where lower temperatures are better. The sensitivity is highest at low currents. This highlights the complex thermal management needs.
  • Relative Humidity: The optimal intake relative humidity was found to be 80%. Lower humidity can lead to membrane dehydration, while higher humidity (100%) can cause cathode flooding, both negatively impacting performance.

Limitations and Future Work

The authors acknowledge that their current analysis, while experimental, primarily focused on the individual impact of parameters. They identify a significant gap in understanding the complex feedback mechanisms and interactions between multiple operating parameters.

Future work will involve:

  • Developing an accurate simulation analysis model (using GT-SUITE software).
  • Employing a Design of Experiments (DOE) approach to rigorously quantify and validate parameter interactions.
  • Analyzing the influence of interactions between pairs of parameters (hydrogen pressure, air pressure, air relative humidity, and coolant temperature) on output voltage.
  • Generating relative sensitivity diagrams to visualize these interactions.
  • Ultimately, optimizing parameters based on these findings to enhance fuel cell performance.

Summary updated

Abstract

In this study, the sensitivity of operating parameters such as the hydrogen and air excess coefficient, cathode inlet pressure, intake relative humidity, and coolant inlet temperature and their effects on the performance of single proton exchange membrane fuel cells (PEMFCs) are experimentally assessed. The results revealed that the fuel cell node voltage increases as the hydrogen and air excess coefficient increases, and the impact of the hydrogen and air excess coefficient on the fuel cell node voltage gradually increases as the current density increases. However, a higher hydrogen and air excess coefficient is not always better. The node voltage increases as the intake pressure increases. However, it is not that a higher intake pressure is always better, but rather that there is an optimal intake pressure value to achieve the best overall performance of the fuel cell. The node voltage increases as the coolant inlet temperature increases at most fuel cell current densities. However, the optimum fuel cell operating inlet temperature is not necessarily higher, as the coolant inlet temperature may have a strong coupling relationship with other operating conditions that will also affect the fuel cell performance. The fuel cell operating inlet temperature may have a strong coupling relationship with the intake relative humidity, and both of these parameters must be well-matched to achieve better fuel cell performance.
BibTeX
@inproceedings{feng2025comprehensive,
  author = {Renhua Feng and Zhanye Hua and Jing Yu and Shaoyang Wang and Lubing Shi and Xing Shu and Zeyu Yan and Jiayi Guo},
  title = {{Comprehensive Experimental Investigation of Operational Parameter Sensitivity in Proton Exchange Membrane Fuel Cell Performance}},
  booktitle = {Batteries},
  year = {2025},
  doi = {10.3390/batteries11070278},
}
Figure