Abstract
Ultra-massive multiple-input and multiple-output (MIMO) systems have been seen as the key radio technology for the advancement of wireless communication systems, due to its capability to better utilize the spatial dimension of the propagation channels. Channel sounding is essential for developing accurate and realistic channel models for the massive MIMO systems. However, channel sounding with large-scale antenna systems has faced significant challenges in practice. The real antenna array based (RAA) sounder suffers from high complexity and cost, while virtual antenna array (VAA) solutions are known for its long measurement time. Notably, these issues will become more pronounced as the antenna array configuration gets larger for future radio systems. In this paper, we propose the concept of multiplicative array (MA) for channel sounding applications to achieve large antenna aperture size with reduced number of required antenna elements. The unique characteristics of the MA are exploited for wideband spatial channel sounding purposes, supported by both one-path and multi-path numerical simulations. To address the fake paths and distortion in the angle delay profile issues inherent for MA in multipath channel sounding, a novel channel parameter estimation algorithm for MA based on successive interference cancellation (SIC) principle is proposed. Both numerical simulations and experimental validation results are provided to demonstrate the effectiveness and robustness of the proposed SIC algorithm for the MA. This research contributes significantly to the channel sounding and characterization of massive MIMO systems for future applications.
Introduction
As the industry pivots toward 6G, wireless systems are expected to deploy "ultra-massive MIMO," utilizing arrays with hundreds or even thousands of antennas. Accurate channel sounding—the process of measuring radio wave interactions with the environment—is critical for designing these systems. However, researchers face a hardware "trilemma": Real Antenna Arrays (RAA) require prohibitively expensive RF chains for every element, while Virtual Antenna Arrays (VAA) take too long to measure dynamic environments. Switched arrays often compromise on spatial resolution. This paper proposes a middle ground: Multiplicative Arrays (MA) that provide high-resolution spatial modeling with a drastically reduced hardware footprint.
Multiplicative Array Architecture
The core innovation lies in replacing a full $M \times N$ grid of antennas, known as a Uniform Rectangular Array (URA), with two thin, orthogonal linear arrays. By mathematically multiplying the signals from these two arrays, the system can synthesize the beam pattern of a much larger rectangular grid.
As shown in Figure 1, the MA approach (c, d) uses significantly fewer elements than the standard URA (a, b). For example, to mimic a $100 \times 100$ array (10,000 elements), an MA would only require approximately 400 elements, representing a massive reduction in hardware complexity and cost.
The Challenge of "Fake Paths"
While hardware-efficient, the multiplicative process introduces a significant artifact: "fake paths" or ghost images. In a multipath environment where signals bounce off multiple surfaces, the multiplication of signals from the two orthogonal arrays creates cross-terms. If two real propagation paths exist, the multiplication produces four results: the two true paths and two "fake paths" with incorrect angles and delays.
Figure 6 illustrates this phenomenon in the $u-v$ space. These ghosts are not random noise; they are deterministic products of the true paths. Understanding this geometry is the key to the researchers' solution.
Successive Interference Cancellation (SIC)
To resolve the ghosting issue, the authors developed a Successive Interference Cancellation (SIC) algorithm. The process is iterative:
- Identify: Detect the strongest path in the measured data.
- Estimate: Determine its parameters (angle, delay, and power).
- Reconstruct: Calculate the specific "fake paths" that this strong path would generate when multiplied with other signals.
- Subtract: Remove both the real path and its associated ghosts from the total signal.
- Repeat: Continue the process until all dominant paths are extracted and the residual signal is minimized.
Key Results and Experimental Validation
The approach was validated using indoor experimental measurements at 27 GHz in a controlled meeting room environment.
- Antenna Thinning: The researchers used 38 antenna elements to achieve results comparable to a 75-element URA, a 49.3% reduction in elements.
- High Accuracy: The SIC algorithm successfully identified six dominant paths with minimal error: within 1° for azimuth angle and 0.5 ns for delay.
- Robustness: The system proved capable of identifying paths even when they were 15 dB weaker than the primary Line-of-Sight (LOS) signal.
Conclusion
By combining the hardware efficiency of Multiplicative Arrays with the precision of the SIC algorithm, this research provides a viable pathway for sounding the ultra-massive MIMO channels of the future. While the algorithm adds computational complexity, the trade-off in reduced hardware cost and measurement time makes it a compelling solution for 6G development. Future work will look toward applying these methods to dynamic outdoor environments and sub-THz frequencies.
Summary updated