CALPHAD-Assisted Analysis of Fe-Rich Intermetallics and Their Effect on the Mechanical Properties of Al-Fe-Si Sheets via Continuous Casting and Direct Rolling

Longfei Li, Xiaolong Li, Lei Shi, Shouzhi Huang, Cong Xu, Guangxi Lu, Shao Kang GuanMetals 2025 · DOI

TL;DR

This paper explores how to optimize Al-Fe-Si alloys for new energy vehicle battery components using a combination of CALPHAD simulations and twin-belt continuous casting and direct rolling (TBCCR). They found that a specific Fe/Si ratio and Mn addition significantly improve mechanical properties and reduce defects, leading to a high-performance alloy suitable for demanding applications.

What Problem Does This Paper Address?

Recycling aluminum scrap for manufacturing often introduces iron (Fe) impurities, which can form detrimental intermetallic phases (FIMCs) in aluminum alloys. These FIMCs increase hardness and reduce deformability, posing challenges for manufacturing processes like continuous casting and direct rolling (TBCCR), which are desirable for their efficiency and eco-friendliness. Furthermore, short-process manufacturing can lead to macro-segregation of Fe and silicon (Si), negatively impacting the quality of the final aluminum sheets. This research aims to address these issues by developing Al-Fe-Si alloys with controlled Fe-rich intermetallics for TBCCR, specifically targeting applications in new energy vehicle batteries where a balance of strength, ductility, and formability is crucial.

Methods

The study employed a multi-faceted approach:

  • CALPHAD Simulations: The Computer Coupling of Phase Diagrams and Thermochemistry (CALPHAD) technique, using PANDAT software, was used to predict the formation of Fe-rich intermetallic phases (α-AlFeSi and β-AlFeSi) based on varying Fe and Si content. This guided the selection of alloy compositions.
  • Twin-Belt Continuous Casting and Direct Rolling (TBCCR): This eco-efficient short-process manufacturing technique was used to produce the experimental Al-Fe-Si and Al-Fe-Si-Mn alloys.
  • Microstructural Analysis: Optical microscopy (OM) and Scanning Electron Microscopy (SEM) with Energy Dispersive X-ray Spectroscopy (EDS) were used to characterize the microstructure, identify intermetallic phases, and analyze surface segregation.
  • Thermal Analysis: Differential Scanning Calorimetry (DSC) was used to determine crystallization temperature ranges (CTR), which are linked to microstructure and segregation.
  • Mechanical Testing: Vickers hardness, tensile testing (ultimate tensile strength, elongation), and cupping tests (formability) were performed on the alloy sheets.
  • Electrochemical Testing: Dynamic polarization curves were used to evaluate corrosion resistance.

Datasets

Not discussed in the paper. The study focuses on experimental alloy development and characterization rather than training on existing datasets.

Key Insights and Ideas

  • Fe/Si Ratio is Key: The Fe/Si atomic ratio plays a critical role in determining the type and distribution of Fe-rich intermetallic phases (α-AlFeSi vs. β-AlFeSi), which in turn significantly influences mechanical properties.
  • β-AlFeSi vs. α-AlFeSi: The needle-like β-AlFeSi phase can be detrimental, leading to defects and reduced ductility, while the α-AlFeSi phase is generally considered less harmful. Controlling the formation of these phases is paramount.
  • Mn as a Refiner and Strengthener: Adding Manganese (Mn) was found to refine the grain structure of cast ingots and enhance the strength of both ingots and rolled sheets. It also helped in transforming detrimental β-AlFeSi into the less harmful α-AlFeSi phase.
  • Surface Segregation Control: Minimizing surface segregation of intermetallic phases is crucial for good surface quality and subsequent processing. The study identified specific alloy compositions that exhibited reduced segregation.
  • Synergistic Optimization: The research demonstrates that achieving optimal performance requires a balance between multiple properties – strength, ductility, formability, and corrosion resistance – which can be achieved through careful control of alloy composition and processing.

Key Results

  • Optimal Al-Fe-Si Composition (without Mn): An Al-Fe-Si alloy with a combined Fe + Si content of 0.7% and an Fe/Si atomic ratio of 3:1 (FS31) achieved an ultimate tensile strength of 145.8 MPa, elongation to failure of 5.7%, and a cupping value of 6.64 mm.
  • Impact of Mn Addition: The addition of Mn refined grain structures and improved strength.
  • Optimized Al-Fe-Si-Mn Composition: A specific composition (Fe + Si = 0.7%, Fe/Si = 1:4 atomic ratio, 0.8 wt.% Mn) was engineered for TBCCR, yielding enhanced comprehensive performance: ultimate tensile strength of 189.4 MPa, elongation to failure of 7.32%, and a cupping value of 7.71 mm. This composition represents an optimal balance of properties.
  • Corrosion Resistance: The study found that the initial Al-Fe-Si alloy exhibited good corrosion resistance, and while Mn addition slightly decreased this resistance, the optimized alloy still offered a favorable balance of properties.

Limitations and Future Work

  • Mn Content Threshold: While Mn addition generally improved properties, ductility began to degrade at 1.2 wt.% Mn, suggesting a need for careful optimization of Mn content.
  • Further Optimization: The paper suggests that the developed compositional design framework, integrating CALPHAD, microstructural analysis, and mechanical/corrosion testing, can be used for further development of high-performance TBCCR alloys. The focus on balancing multiple properties indicates a path towards alloys tailored for specific demanding applications.

Summary updated

Abstract

As an eco-efficient short-process manufacturing technique for aluminum alloys, twin-belt continuous casting and direct rolling (TBCCR) demonstrates significant production advantages. In this study, an Al-Fe-Si alloy system with different Fe-rich intermetallics (α-AlFe(Mn)Si and β-AlFe(Mn)Si) via TBCCR was developed for new energy vehicle batteries, utilizing the Computer Coupling of Phase Diagrams and Thermochemistry (CALPHAD) technique. Comprehensive microstructure and surface segregation analyses of continuous casted ingots and direct-rolled sheets revealed that the Al-Fe-Si alloy with a combined Fe + Si content of 0.7% and an optimal Fe/Si atomic ratio of 3:1 (FS31) presents optimized mechanical properties: ultimate tensile strength of 145.8 MPa, elongation to failure of 5.7%, accompanied by a cupping value of 6.64 mm. Notably, Mn addition further refined the grain structure of casting ingots and enhanced the strength of both ingots and rolled sheets. Among the experimental alloys, FS14 (optimal Fe/Si atomic ratio of 1:4) sheets displayed the least surface segregation upon Mn incorporation. Through systematic optimization, an Al-Fe-Si-Mn alloy composition (Fe + Si = 0.7%, Fe/Si = 1:4 atomic ratio, 0.8 wt.% Mn) was engineered for TBCCR processing, achieving enhanced comprehensive performance: ultimate tensile strength of 189.4 MPa, elongation to failure of 7.32%, and cupping value of 7.71 mm. This composition achieves an optimal balance between grain refinement, mechanical properties (strength–plasticity synergy), formability (cupping value), and corrosion resistance (corrosion current density). The performance optimization strategy integrates synergistic improvements in strength, ductility, and corrosion resistance, providing valuable guidance for developing high-performance aluminum alloys suitable for the TBCCR process.
BibTeX
@inproceedings{li2025calphad,
  author = {Longfei Li and Xiaolong Li and Lei Shi and Shouzhi Huang and Cong Xu and Guangxi Lu and Shao Kang Guan},
  title = {{CALPHAD-Assisted Analysis of Fe-Rich Intermetallics and Their Effect on the Mechanical Properties of Al-Fe-Si Sheets via Continuous Casting and Direct Rolling}},
  booktitle = {Metals},
  year = {2025},
  doi = {10.3390/met15060578},
}
Figure