Abstract
(1) Background: The Cal Poly Rose Float is currently powered by a pair of V-8 internal combustion engines. This is the second project in a three-phase effort to replace the existing drive engine with an electric motor powered by a DC bus. The main goal of this phase of the project is to get the motor selected in phase one spinning. (2) Results: Originally, the project involved programming a microcontroller to achieve motor control. The decision was made, early on, to approach this task in a different manner due to the team’s minimal background in programming and mechatronics. The team decided to purchase and implement a commercially available variable frequency drive to get the motor spinning, and to offer a more sophisticated level of control. After extensive research, planning, purchasing of required components, and connectivity considerations, sufficient motor control was achieved. (3) Conclusion: The selection of a variable frequency drive to gain motor control was successful, and the goals of phase 2 in the Cal Poly electric vehicle project were accomplished. The project is ready to enter the next phase which is to be completed by another team of students.
Introduction
The Cal Poly Rose Float is a student-led engineering tradition that showcases complex mechanical and floral design on a national stage. However, the traditional propulsion system—dual V-8 internal combustion engines (ICEs)—presents significant operational challenges. These engines generate immense heat within the cramped, enclosed skeleton of the float, requiring complex cooling systems to protect student operators. Furthermore, ICEs produce noise and exhaust gases that detract from the parade experience and increase the vehicle's curb weight and environmental footprint.
This project represents the second phase of a multi-year effort to transition the float to a fully electric drivetrain. The overarching goal is to replace the legacy engines with a "green" electric system. This specific phase focuses on the "mechatronics gap": taking the motor selected in Phase 1 and developing a reliable system to control its speed and torque before final battery integration.
Methodology
The team evaluated three primary control strategies using a decision matrix: a custom microcontroller, a Volts per Hertz (V/F) Variable Frequency Drive (VFD), and Flux Vector Control. While the original plan favored a custom build using Atmel AVR microcontrollers, the team made a strategic pivot to a commercial Fuji Frenic Series VFD. This shift was driven by the need for industrial-grade reliability and built-in safety features essential for a high-stakes public event.
To validate the motor selection, the team utilized a custom Excel-based simulation model to calculate power and torque requirements across three critical scenarios: a 10 mph transport speed, a 3.5 mph hill climb at a 6% grade, and a 6.5 mph parade pace at a 2% grade. These simulations confirmed that the Marathon BlueMax Y513-A775 AC motor was appropriately sized for the float's weight and drag. Bench testing was conducted using a high-end Ametek Programmable DC Power Supply to simulate the future battery bus safely.
System Specifications and Performance
The project established rigorous performance parameters to ensure the electric drivetrain met the safety and operational standards of the Rose Parade. The team successfully achieved full-speed control of the 40hp induction motor using a potentiometer-based analog input, meeting the requirement for motor operation under analog control.
A critical success was the validation of the Emergency Stop (E-stop) system. Tested at 48V, the system successfully cut power and stopped the motor in under 0.1 seconds, meeting the target for Spec #1. Additionally, the motor was successfully run at the RPMs required for parade operation (approximately 1727 RPM) under no-load conditions.
Key Insights and Future Work
A major takeaway from this phase was the prioritization of reliability over novelty. By opting for a professional VFD, the team gained built-in safety features like under-voltage protection that would have been difficult to replicate in a student-coded system. Furthermore, the transition to electric propulsion simplifies the vehicle architecture by eliminating the need for complex convective cooling systems for the operators.
However, limitations remain. The current system is "open-loop" (V/F control), meaning the motor will not automatically compensate for inclines. Future phases will need to implement encoder-based "closed-loop" vector control to maintain constant speed regardless of the parade route's grade. Additionally, high-torque operation will require custom-machined flange adapters to prevent shaft misalignment.
Conclusion
Phase 2 of the Cal Poly Rose Float electric vehicle project successfully transitioned from theoretical motor selection to functional control. With a successful VFD implementation and safety verification, the project is positioned for Phase 3: the integration of a battery bank, mounting of the dual-wheel drive system, and full-load road testing on the float chassis.
Summary updated