Boosting the Lithium Storage Properties of a Flexible Li4Ti5O12/Graphene Fiber Anode via a 3D Printing Assembly Strategy

C.y. Zhao, Rui Wang, Biao Fang, Han Liang, Biyuan Nie, Ruyi Wang, Biao Xu, Songyang Feng, Ruqing Li, Shuaifei Li, Yuhui Xiong, Yuye Shao, Runwei MoBatteries 2023 · DOI

TL;DR

This paper presents a novel 3D printing strategy to create flexible lithium-ion battery anodes using a Li4Ti5O12/graphene fiber composite. By employing a vitamin C-reduced graphene oxide ink, the researchers achieved enhanced conductivity and a robust 3D conductive network, leading to superior electrochemical performance and mechanical flexibility for next-generation wearable electronics.

What Problem Does This Paper Address?

The rapid advancement of wearable devices, smart textiles, and flexible electronics has created a critical demand for energy storage solutions that can match their inherent flexibility and durability. Traditional lithium-ion batteries, with their rigid electrode materials and manufacturing processes, are ill-suited for these applications, often failing under repeated bending and stretching. While one-dimensional flexible fiber electrodes offer a promising avenue, achieving a balance between excellent electrochemical performance and robust mechanical properties has remained a significant challenge. This often involves a trade-off: improving mechanical strength can compromise conductivity, and vice-versa.

Methods

The core of this work lies in a 3D printing assembly strategy utilizing a custom-formulated ink. The ink comprises:

  • Li4Ti5O12 (LTO): The active anode material.
  • Polyvinylidene fluoride (PVDF): A binder to enhance mechanical properties.
  • Reduced Graphene Oxide (rGO): Synthesized in-situ using a green reducing agent, vitamin C, to improve conductivity.
  • Graphene Oxide (GO): The precursor for rGO.

The fabrication process involves:

  1. Ink Preparation: Mixing LTO, PVDF, and GO with a solvent (NMP).
  2. 3D Printing: Extruding the ink through a nozzle into deionized water. This triggers a solvent exchange process, causing PVDF to precipitate and form a fiber electrode.
  3. Separator Coating: Passing the electrode through a PVDF-HFP solution to form a separator layer on its surface.
  4. Drying: Final drying at room temperature.

This direct ink writing (DIW) approach allows for precise control over the shape, size, and structure of the fiber electrodes. The use of vitamin C for GO reduction is highlighted as a simple, efficient, and environmentally friendly method to enhance conductivity.

Datasets

Not discussed in the paper. The study focuses on the fabrication and characterization of a novel electrode material.

Key Insights and Ideas

  • Vitamin C as a Green Reducer: Demonstrates the efficacy of a simple, environmentally friendly agent (vitamin C) for reducing GO to rGO in a single step, significantly improving conductivity without complex procedures.
  • 3D Conductive Network Formation: The high specific surface area of rGO, combined with the DIW process and solvent exchange, creates an intrinsic 3D conductive network within the fiber electrode. This network is crucial for efficient electron and ion transport.
  • Synergistic Mechanical and Electrochemical Properties: The study successfully overcomes the typical trade-off by achieving both high flexibility (35% elongation at break) and excellent electrochemical performance, suggesting a well-balanced material design.
  • Precise Structural Control via 3D Printing: The DIW method allows for the fabrication of electrodes with tailored shapes and sizes, opening doors for complex, integrated flexible electronic designs.
  • Porous Structure for Ion Transport: The solvent exchange process leads to the formation of micropores on the electrode surface, which facilitates electrolyte adsorption and ion transport, further boosting electrochemical performance.

Key Results

  • Mechanical Performance: The flexible Li4Ti5O12/graphene fiber electrode exhibits an elongation at break of 35%.
  • Electrochemical Performance:
    • Initial discharge specific capacity: 182.8 mAh g⁻¹ at 1C.
  • Capacity retention after 100 cycles: 83%.
  • Rate performance: Capacities of 191.5, 175.3, 164.4, 156.2, and 127.2 mAh g⁻¹ at rates of 0.1C, 0.2C, 0.5C, 1C, and 2C, respectively, with good recovery upon returning to 0.1C.
  • Conductivity Enhancement: The conductivity of rGO is 10³ times higher than that of GO.

Limitations and Future Work

Limitations: * While the study demonstrates excellent performance, the paper notes that the impedance of the LTO/rGO fiber electrode increases after 100 cycles, leading to a slight decrease in charge-discharge specific capacity. This suggests potential for further optimization to improve long-term stability. * The study focuses on the anode material; future work would involve integrating this anode with a suitable cathode and electrolyte to create a complete flexible battery.

Future Work: The authors suggest that this preparation method, being simple, environmentally friendly, and enabling mass production, has broad application prospects. Future research could explore:

  • Scaling up the production of these flexible fiber electrodes.
  • Integrating these anodes into full flexible battery devices for real-world applications.
  • Further optimizing the electrode composition and structure to enhance cycle life and energy density.
  • Investigating the long-term stability under various bending and stretching conditions.

Summary updated

Abstract

Traditional lithium-ion batteries cannot meet the high flexibility and bendability requirements of modern flexible electronic devices due to the limitations of the electrode material. Therefore, the development of high-performance flexible energy storage devices is of great significance for promoting flexible electronics. In recent years, one-dimensional flexible fiber lithium-ion batteries have been rapidly developed due to their advantages of high flexibility and bendability. However, it remains highly challenging to realize 1D flexible fiber lithium-ion batteries with excellent electrochemical properties and good mechanical performance. In this work, a reduced graphene oxide-based printing ink is proposed for the fabrication of flexible Li4Ti5O12/graphene fiber electrodes using a 3D printing assembly strategy. It is noteworthy that the green reducing agent vitamin C was used to reduce the graphene oxide in one step, which improved the conductivity of the fiber electrode. Furthermore, a 3D conductive network was constructed inside the fiber electrodes due to the high specific surface area of the reduced graphene oxide, which enhanced the electronic conductivity and ion mobility. The fiber electrode not only exhibits good mechanical performance, but also has excellent electrochemical properties. Equally importantly, the method is simple and efficient, and the working environment is flexible. It can precisely control the shape, size and structure of the one-dimensional fiber flexible electrode, which is of great significance for the development of future flexible electronic devices.
BibTeX
@inproceedings{zhao2023boosting,
  author = {C.Y. Zhao and Rui Wang and Biao Fang and Han Liang and Biyuan Nie and Ruyi Wang and Biao Xu and Songyang Feng and Ruqing Li and Shuaifei Li and Yuhui Xiong and Yuye Shao and Runwei Mo},
  title = {{Boosting the Lithium Storage Properties of a Flexible Li4Ti5O12/Graphene Fiber Anode via a 3D Printing Assembly Strategy}},
  booktitle = {Batteries},
  year = {2023},
  doi = {10.3390/batteries9100493},
}
Figure