Bio-inspired multimodal soft actuator with environmental self-adaptation

Chi Chen, Zixiao Liu, Pengju Shi, Yusen Zhao, Sidi Duan, Yingjie Du, Yichen Yan, Muqing Si, Tetsuya Iwasaki, Ximin HeNature Communications 2025 · DOI

TL;DR

Researchers have developed a novel bio-inspired soft actuator that can autonomously switch between three distinct motion modes (tracking, undulation, and oscillation) in response to environmental changes, mimicking the adaptive capabilities of marine life. This breakthrough, achieved through a cleverly engineered asymmetric structure and intrinsic feedback mechanisms, promises to unlock higher levels of autonomy for soft robots in complex and dynamic environments.

What Problem Does This Paper Address?

Current autonomous soft robots, while capable of self-sustained motion, often suffer from a lack of adaptability. They are typically designed for single-mode actuation and require human intervention to switch behaviors, hindering their ability to navigate and operate effectively in diverse and changing environments. This limitation is particularly problematic for miniaturized and lightweight robots where complex control systems and external power sources are impractical. The paper aims to bridge this gap by creating a soft actuator that exhibits "physical intelligence"—the ability to sense, decide, and actuate autonomously based on environmental cues, much like living organisms.

Methods

The core innovation lies in the design of a light-responsive soft actuator composed of a photoactive-passive-photoactive trilayer. The key to its multimodal behavior is the introduction of engineered asymmetry through a localized defect (an unbound region) between the layers. This asymmetry, when subjected to constant near-infrared (NIR) light, creates a stress imbalance.

The actuator leverages intrinsic photo-thermo-mechanical feedback loops. When exposed to light, the photoactive layers heat up, causing them to expand. The asymmetric defect region allows for controlled buckling and bending. The system exhibits two bifurcation points that govern the transitions between motion modes:

  1. Tracking-Undulation Bifurcation: At lower light intensities, the actuator tracks the light source. As intensity increases, the stress imbalance leads to buckling, initiating undulation.
  2. Undulation-Oscillation Bifurcation: At higher light intensities, the actuator transitions from undulation to oscillation.

This dynamic structural response is achieved without external control units, relying solely on the material's inherent properties and the energy input. The researchers also explored the influence of geometrical parameters (defect region length and position) on these bifurcations.

Datasets

Not discussed in the paper. The research focuses on the design and experimental characterization of a novel material system and its behavior.

Key Insights and Ideas

  • Physical Intelligence at the Material Level: The actuator demonstrates that complex adaptive behaviors can be encoded directly into the material's structure and properties, reducing the need for external electronics and control.
  • Bio-Inspiration from Gymnura micrura: The study draws a direct parallel between the actuator's multimodal switching and the Gymnura micrura's ability to adapt its locomotion for different environments (foraging vs. cruising).
  • Two Bifurcation Points for Three Modes: The elegant design with two critical energy thresholds allows for a seamless transition through three distinct, functional motion modes.
  • Environmental Adaptability: The actuator shows remarkable self-adaptation to changes in light intensity, fluid viscosity, temperature, and even physical constraints, highlighting its robustness.
  • Beyond Locomotion: The multimodal capability opens doors for applications in fluid dynamics (vortex generation), electronics (triboelectric nanogenerators), and environmental monitoring.

Key Results

  • The actuator successfully demonstrated three distinct motion modes: tracking, undulation, and oscillation.
  • Self-adaptation was observed across various environmental conditions:
  • Viscosity: Increased viscosity led to transitions from oscillation to undulation, and finally to static tracking.
  • Temperature: Higher temperatures also influenced motion modes, demonstrating adaptation to thermal environments.
  • Physical Constraint: The actuator could navigate obstacles, with undulation enabling higher maneuverability compared to a symmetric counterpart.
  • The actuator showed broad-spectrum operation across visible and NIR light.
  • The system exhibited self-excitation, meaning it could initiate motion without external triggering, unlike symmetric structures.
  • The undulation mode was found to have a higher peak output efficiency, while oscillation offered a higher average output, mirroring the Gymnura micrura's strategy.

Limitations and Future Work

  • Material System Specificity: While the authors explored extending the concept to other material systems, the core design relies on specific photo-thermo-mechanical properties of LCEs and PDMS. Further research is needed to generalize this to a wider range of soft materials.
  • Defect Engineering: The precise control and fabrication of the defect region are crucial. While they demonstrated reproducibility, scaling this to mass production might present challenges.
  • Energy Efficiency Trade-offs: The paper notes a trade-off between peak and average energy output for undulation and oscillation, respectively. Optimizing for specific applications might require further tuning.
  • Future Work: The authors suggest extending this multimodal adaptation to more complex robotic systems, exploring applications in fluid dynamics, electronics, and environmental monitoring, and further enhancing the autonomy and functionality of soft robots. They also propose investigating the impact of additional defects on motion modes.

Summary updated

Abstract

Autonomous soft robots with built-in feedback can achieve self-sustained motion under constant, untethered stimuli. However, these systems are constrained to single-mode actuation within a fixed structure under the same type of stimulus and require human intervention to switch modes, lacking the robust and efficient self-adaptation of living organisms in changing environments. Inspired by Gymnura micrura, we developed a light-responsive soft actuator with engineered asymmetry and a dynamic structure, integrating two distinct built-in feedback mechanisms governed by intrinsic bifurcation. Thus, the actuator can seamlessly switch between three different motion modes-tracking, undulation, and oscillation-exhibiting self-adaptation to environmental changes (e.g., light intensity, viscosity, temperatures, and physical contact). Furthermore, this multimodal capability facilitates unique environmental interactions, expanding applications beyond locomotion to include fluid dynamics, electronics, and environmental monitoring. Such an advancement in physical intelligence represents a pivotal step toward next-generation autonomous soft robotic systems, unlocking higher-level autonomy and unprecedented adaptive behaviors.
BibTeX
@inproceedings{chen2025bio,
  author = {Chi Chen and Zixiao Liu and Pengju Shi and Yusen Zhao and Sidi Duan and Yingjie Du and Yichen Yan and Muqing Si and Tetsuya Iwasaki and Ximin He},
  title = {{Bio-inspired multimodal soft actuator with environmental self-adaptation}},
  booktitle = {Nature Communications},
  year = {2025},
  doi = {10.1038/s41467-025-62328-2},
}
Figure