Bilayer and three dimensional conductive network composed by SnCl2 reduced rGO with CNTs and GO applied in transparent conductive films

Ying Tian, Ning Guo, Wenyi Wang, Wenming Geng, Li‐Chao Jing, Tao Wang, Xiao–Tong Yuan, Ze-Ru Zhu, Yicheng Ma, Hong‐Zhang GengScientific 2021 · DOI

TL;DR

This paper presents a novel, environmentally friendly method for creating transparent conductive films using reduced graphene oxide (rGO) and carbon nanotubes (CNTs). By employing a mild SnCl2/ethanol reduction and a subsequent nitric acid treatment, they achieved bilayer films with excellent conductivity and transparency, offering a promising alternative to traditional indium tin oxide (ITO).

What Problem Does This Paper Address?

Indium tin oxide (ITO) has been the go-to material for transparent conductive films (TCFs) due to its high conductivity and transparency. However, indium is a rare and expensive element, and ITO films are brittle, limiting their use in flexible electronics. Graphene and its derivatives, like graphene oxide (GO) and reduced graphene oxide (rGO), along with carbon nanotubes (CNTs), offer potential alternatives due to their excellent electrical, optical, and mechanical properties. The challenge lies in efficiently and affordably producing high-quality rGO and integrating it with CNTs into TCFs without harsh conditions or toxic byproducts. Existing methods for rGO production often involve high temperatures or toxic chemicals, and achieving optimal performance requires careful control of material ratios and processing steps.

Methods

The researchers developed a multi-step process for fabricating their TCFs:

  • Mild rGO Synthesis: They used a SnCl2/ethanol solution as a reductant for GO. This method is highlighted as being environmentally friendly, requiring mild reaction conditions (room temperature), and producing no harmful byproducts, unlike traditional methods.
  • CNT Integration: Single-walled carbon nanotubes (SWCNTs) were dispersed and mixed with GO to form hybrid solutions.
  • Film Deposition: The GO/CNT hybrid solutions were sprayed onto polyethylene terephthalate (PET) substrates to form thin films.
  • Reduction and Post-Treatment:
    • Reduction: The GO in the films was reduced to rGO using the SnCl2/ethanol solution. This was performed in two stages (Reduction 1 and Reduction 2) to optimize conductivity.
  • Acid Treatment: A crucial step involved immersing the reduced films in nitric acid. This served multiple purposes: removing residual dispersants (like SDBS) and byproducts (SnO2), and importantly, introducing nitrogen doping into the rGO, which further enhances conductivity.
  • Bilayer Structure: To further improve performance, a bilayer structure was created. The first layer underwent reduction and acid treatment, while the second layer was treated with nitric acid only. This approach aimed to optimize conductivity and surface properties.
  • Characterization: A suite of techniques was employed to verify the material's properties and the effectiveness of the treatments, including SEM, XPS, Raman spectroscopy, XRD, AFM, and UV-Vis spectrophotometry.

Datasets

Not discussed in the paper. The study focuses on the synthesis and characterization of novel materials rather than training on existing datasets.

Key Insights and Ideas

  • Mild and Green Reduction: The SnCl2/ethanol method offers a significant advantage by avoiding harsh conditions and toxic chemicals typically associated with rGO production. This makes the process more scalable and safer.
  • Synergistic Combination: The combination of rGO and CNTs creates a three-dimensional conductive network that complements each other's properties, leading to improved conductivity.
  • Multifaceted Nitric Acid Treatment: Nitric acid plays a critical role beyond just removing impurities; its N-doping effect on rGO is key to enhancing conductivity.
  • Bilayer Structure Optimization: The bilayer approach, with specific treatments for each layer, allows for fine-tuning of both electrical and surface properties, leading to superior performance.
  • Surface Roughness Reduction: The incorporation of GO and rGO effectively reduces the surface roughness of the films, which is crucial for applications like organic light-emitting diodes (OLEDs).

Key Results

The researchers successfully fabricated transparent conductive films with a bilayer and three-dimensional structure. The optimal films exhibited:

  • High Transmittance: 83.45% at 58.8 Ω/sq and 79.07% at 47.5 Ω/sq.
  • Low Sheet Resistance: Achieved values as low as 47.5 Ω/sq.
  • Excellent Performance Index: Corresponding [Formula: see text] values of 33.8 and 31.8, indicating a good balance between transparency and conductivity.
  • Reduced Surface Roughness: The films showed significantly lower surface roughness compared to pure CNT films, with RMS roughness values of 7.63 nm and 6.74 nm for S-RGO/CNT0.5 and S-RGO/CNT1.0, respectively.

Limitations and Future Work

  • Residual SnO2: While nitric acid treatment effectively reduced SnO2 byproducts, a small amount still remained on the surface.
  • Slight Oxidation: The nitric acid treatment, while beneficial for doping, could cause slight re-oxidation of rGO, leading to a minor increase in oxygen-containing groups compared to films treated only by reduction.
  • Future Work: The authors suggest that these transparent conductive films are expected to be used in future flexible photoelectric devices, implying potential applications in areas like flexible displays, solar cells, and touch screens. Further optimization of the bilayer structure and reduction parameters could lead to even better performance.

Summary updated

Abstract

Graphene oxide (GO), reduced graphene oxide (rGO) and carbon nanotubes (CNTs) have their own advantages in electrical, optical, thermal and mechanical properties. An effective combination of these materials is ideal for preparing transparent conductive films to replace the traditional indium tin oxide films. At present, the preparation conditions of rGO are usually harsh and some of them have toxic effects. In this paper, an SnCl<sub>2</sub>/ethanol solution was selected as the reductant because it requires mild reaction conditions and no harmful products are produced. The whole process of rGO preparation was convenient, fast and environmentally friendly. Then, SEM, XPS, Raman, and XRD were used to verify the high reduction efficiency. CNTs were introduced to improve the film conductive property. The transmittance and sheet resistance were the criteria used to choose the reduction time and the content ratios of GO/CNT. Thanks to the post-treatment of nitric acid, not only the by-product (SnO<sub>2</sub>) and dispersant in the film are removed, but also the doping effect occurs, which are all conducive to reducing the sheet resistances of films. Ultimately, by combining rGO, GO and CNTs, transparent conductive films with a bilayer and three-dimensional structure were prepared, and they exhibited high transmittance and low sheet resistance (58.8 Ω/sq. at 83.45 T%, 47.5 Ω/sq. at 79.07 T%), with corresponding [Formula: see text] values of 33.8 and 31.8, respectively. In addition, GO and rGO can modify the surface and reduce the film surface roughness. The transparent conductive films are expected to be used in photoelectric devices.
BibTeX
@inproceedings{tian2021bilayer,
  author = {Ying Tian and Ning Guo and Wenyi Wang and Wenming Geng and Li‐Chao Jing and Tao Wang and Xiao–Tong Yuan and Ze-Ru Zhu and Yicheng Ma and Hong‐Zhang Geng},
  title = {{Bilayer and three dimensional conductive network composed by SnCl2 reduced rGO with CNTs and GO applied in transparent conductive films}},
  booktitle = {Scientific},
  year = {2021},
  doi = {10.1038/s41598-021-89305-1},
}
Figure