Bidirectional Drive with Inhibited Hysteresis for Piezoelectric Actuators

Weiqing Huang, Junkai Lian, Dawei An, Mingyang Chen, Yinfeng LeiSensors 2022 · OpenReview

TL;DR

This paper introduces a novel bidirectional piezoelectric actuator that actively drives both the push and pull strokes, significantly reducing the inherent asymmetry and hysteresis of traditional piezoelectric actuators. This design achieves a substantial improvement in positioning accuracy, with a maximum displacement of 91.45 µm and a resolution of 35 nm, while reducing nonlinear error by over 60%.

What Problem Does This Paper Address?

Precision positioning is critical in fields like microelectronics, aerospace, and advanced manufacturing. Piezoelectric actuators (PZTs) are favored for their small size, fast response, and high force, but conventional PZT actuators suffer from significant limitations: their displacement curves are asymmetrical and non-linear due to hysteresis. This means the actuator's response depends on its previous state, leading to large positioning errors and reduced accuracy. While displacement amplification mechanisms can increase stroke, they often exacerbate hysteresis. This paper tackles the challenge of creating a PZT actuator that offers both a large, precise displacement and a symmetrical, low-hysteresis response.

Methods

The researchers propose a bidirectional active drive piezoelectric actuator utilizing a series rhombus mechanism. Unlike traditional designs where the return stroke relies on the elastic recovery of the mechanism, this new design employs two PZT stacks, each driving one of the rhombus mechanisms in a coordinated manner.

Key methodological aspects include:

  • Theoretical Modeling: A theoretical model of the rhombus mechanism was developed based on beam deformation theory to analyze how structural parameters (thickness, length, width, and inclination angle of flexible beams) affect displacement magnification and input stiffness.
  • Finite Element Method (FEM): COMSOL Multiphysics was used for static and dynamic analysis to verify the theoretical model, predict stress distribution, displacement, and natural frequencies.
  • Prototype Fabrication and Testing: A prototype was manufactured using wire cutting technology. An experimental setup was built to test the actuator's performance, including maximum displacement, resolution, hysteresis, response speed, and resonance frequency.

Datasets

Not discussed in the paper. The study relies on theoretical modeling, FEM simulations, and experimental measurements from a fabricated prototype.

Key Insights and Ideas

  • Active Bidirectional Drive is Key: The core innovation is actively driving both the extension and contraction of the actuator. This overcomes the passive return stroke limitation of conventional designs, leading to symmetry and reduced hysteresis.
  • Rhombus Mechanism for Amplification: The rhombus mechanism, with its central symmetry and triangular amplification principle, provides a compact structure with a good amplification ratio.
  • Structural Parameter Optimization: The study systematically analyzed how flexible beam dimensions (thickness, width, length) and inclination angle influence displacement magnification and input stiffness, guiding the design for optimal performance.
  • Hysteresis Reduction is Significant: By actively controlling both push and pull strokes, the actuator achieves a symmetrical hysteresis loop and a substantial reduction in nonlinear error compared to a standard PZT stack.

Key Results

  • Maximum Displacement: The prototype achieved a maximum output displacement of 91.45 µm.
  • Resolution: The actuator demonstrated a high resolution of 35 nm.
  • Nonlinear Error Reduction: The nonlinear error was reduced by 62.94% compared to the hysteresis loop of a standard piezoelectric stack.
  • Displacement Magnification: The measured displacement magnification was 5.71 times, slightly higher than theoretical predictions.
  • Resonance Frequencies: The first two resonance frequencies were found to be 1455.4 Hz and 1615 Hz (from FEM), indicating suitability for low-frequency precision positioning.
  • Response Time: The actuator exhibited a response time in the range of 11–13 ms.

Limitations and Future Work

  • Processing and Manufacturing Errors: The authors acknowledge that discrepancies between theoretical calculations and experimental results are partly due to errors in processing and manufacturing the prototype.
  • Simplified Theoretical Model: The theoretical model primarily considers the deformation of the flexible beam, potentially neglecting other contributing factors, which could lead to deviations.
  • Future Work: While not explicitly detailed, the paper's success in reducing hysteresis and improving accuracy suggests future work could focus on:
  • Further optimization of the rhombus mechanism design for even higher stroke or stiffness.
  • Integration into closed-loop control systems to leverage the improved linearity.
  • Exploring different materials or fabrication techniques to further minimize manufacturing imperfections.
  • Investigating the actuator's performance under dynamic loading and varying environmental conditions.

Summary updated

Abstract

Piezoelectric actuators with a flexible displacement amplification structure are widely used in the fields of precision driving and positioning. The displacement curve of conventional piezoelectric actuators is asymmetrical and non-linear, which leads to large non-linear errors and reduced positioning accuracy of these piezoelectric actuators. In this paper, a bidirectional active drive piezoelectric actuator is proposed, which suppresses the hysteresis phenomenon to a certain extent and reduces the non-linear error. Based on the deformation theory of the beam, a theoretical model of the rhombus mechanism was established, and the key parameters affecting the drive performance were analyzed. Then, the static and dynamic characteristics of series piezoelectric actuators were analyzed by the finite element method. A prototype was manufactured and the output performance was tested. The results show that the actuator can achieve a bidirectional symmetric output of amplification displacement, with a maximum value of 91.45 μm and a resolution of 35 nm. In addition, compared with the hysteresis loop of the piezoelectric stack, the nonlinear error is reduced by 62.94%.
BibTeX
@inproceedings{huang2022bidirectional,
  author = {Weiqing Huang and Junkai Lian and Dawei An and Mingyang Chen and Yinfeng Lei},
  title = {{Bidirectional Drive with Inhibited Hysteresis for Piezoelectric Actuators}},
  booktitle = {Sensors},
  year = {2022},
  url = {https://openreview.net/forum?id=j63Zbo0lQF},
}
Figure