Assessing the Effects of Different Process Parameters on the Pyrolysis Behaviors and Thermal Dynamics of Corncob Fractions

Xiwen Yao, Kaili Xu, Yu LiangBioResources 2017 · DOI

TL;DR

This study investigates how heating rate, gas flow, and particle size affect the pyrolysis of corncobs (CC) for bio-syngas production. The findings reveal that higher heating rates and specific particle sizes (154-280 µm) are optimal for maximizing bio-syngas yield, offering valuable insights for optimizing biomass conversion processes.

What Problem Does This Paper Address?

The world is increasingly looking for sustainable energy alternatives to fossil fuels, and biomass is a promising renewable resource. Pyrolysis, a thermochemical conversion process, is a key method for transforming biomass into valuable products like bio-syngas. However, the efficiency and product distribution of biomass pyrolysis are highly sensitive to various process parameters. This paper specifically addresses the need to understand how key parameters – heating rate, gas flow, and particle size – influence the pyrolysis behavior and thermal dynamics of corncobs (CC), a readily available agricultural waste. By elucidating these relationships, the research aims to identify optimal conditions for maximizing bio-syngas production from CC, contributing to more efficient biomass utilization.

Methods

The researchers employed a quantitative approach using Thermogravimetric Analysis (TGA) coupled with Mass Spectrometry (MS). This combined technique allows for simultaneous measurement of weight loss during heating (TGA) and identification of the evolved gaseous products (MS).

  • TGA-DSC: Thermogravimetric analysis (TG) and Differential Scanning Calorimetry (DSC) were used to monitor weight changes and heat flow during pyrolysis across a temperature range of 25 to 1200 °C.
  • MS: A quadrupole mass spectrometer (QMS) was used to identify and quantify the gaseous products (CO, CO2, CH4, H2) released during pyrolysis.
  • Parameter Variation: The study systematically varied three key parameters:
  • Heating Rate: Tested at 5, 10, and 20 °C/min.
  • Gas Flow: Tested at 30, 60, and 90 mL/min using helium as the carrier gas.
  • Particle Size: Tested with four size ranges: ≤ 74 µm, 74 µm < d ≤ 154 µm, 154 µm < d ≤ 280 µm, and 280 µm < d ≤ 450 µm.
  • Kinetic Analysis: The Coats-Redfern method was applied to the TGA data to determine pyrolysis kinetic parameters, specifically activation energy (E) and the pre-exponential factor (A).

The use of TGA-MS is a standard but powerful method for this type of analysis. The systematic variation of multiple parameters and the subsequent kinetic analysis are the core of the experimental design.

Datasets

Not discussed in the paper. The study relies on experimental data generated from the pyrolysis of corncob samples prepared by the researchers.

Key Insights and Ideas

  • Heating Rate Matters for Completeness: Higher heating rates lead to more complete decomposition of corncobs. This suggests that faster heating can drive the pyrolysis reactions more effectively, breaking down more of the biomass.
  • Gas Flow's Dual Role: Increasing gas flow initially decreases the onset temperature of pyrolysis and increases overall weight loss. This is attributed to the carrier gas efficiently removing volatile products, which can accelerate cracking reactions. However, excessively high gas flow might lead to less efficient capture of certain gases.
  • Particle Size is Crucial for Bio-syngas Distribution: Smaller particles have a higher surface-area-to-volume ratio, facilitating faster heat and mass transfer. However, the optimal particle size for bio-syngas production was found to be in the range of 154 µm < d ≤ 280 µm. Larger particles showed better overall pyrolysis performance, but this specific size range appears to strike a balance for gas production.
  • Syngas Product Trends:
    • CO, CO2, and CH4 emissions generally increase with higher heating rates and decrease with increased gas flow.
  • H2 emission shows a more complex behavior, with its yield potentially improving with reduced residence time (higher gas flow) when CO and CH4 yields decrease.
  • Kinetic Insights: The activation energies for corncob pyrolysis were found to be relatively low (64-80 kJ·mol⁻¹) compared to other biomass sources, indicating that corncobs are relatively easy to pyrolyze. Increasing heating rate and gas flow generally decreased the activation energy, suggesting these conditions facilitate the reaction.

Key Results

  • Optimal Conditions for Bio-syngas: The study identified that pyrolyzing corncob particles of 154 µm < d ≤ 280 µm at a heating rate of 20 °C/min with a gas flow of 30-60 mL/min is most appropriate for industrial bio-syngas production.
  • Total Weight Loss: Higher heating rates led to significantly increased total weight loss, reaching 77.23% at 20 °C/min compared to 47.79% at 5 °C/min.
  • Gas Flow Impact: Increasing gas flow from 30 to 90 mL/min slightly increased total weight loss (from 75.94% to 77.46%) and decreased the starting pyrolysis temperature.
  • Particle Size Impact: Larger particles (e.g., >280-450 µm) showed better overall pyrolysis performance, with a total weight loss of 80.38%, compared to smaller particles (≤74 µm) at 75.01%. However, the 154-280 µm range was highlighted for optimal bio-syngas production.
  • Activation Energy: Values ranged from 64 to 80 kJ·mol⁻¹, with lower values observed at higher heating rates and gas flows.

Limitations and Future Work

  • Limited Gas Flow Range: While three gas flow rates were tested, a more extensive range might reveal finer nuances in gas product distribution.
  • Particle Size Optimization: While a range of particle sizes was tested, further refinement within the optimal range (154-280 µm) could potentially yield even better results.
  • Catalytic Effects: The study focused on non-catalytic pyrolysis. Investigating the influence of catalysts could further enhance bio-syngas yields and selectivity.
  • Industrial Scale-up: The study was conducted at a laboratory scale. Future work should focus on validating these findings at an industrial scale, considering factors like heat transfer and reactor design.
  • Bio-syngas Composition: While the study identified optimal conditions for production, further detailed analysis of the bio-syngas composition (e.g., CO/H2 ratio, calorific value) under these conditions would be beneficial for practical applications.

Summary updated

Abstract

The influence of heating rate, gas flow, and biomass particle size on the pyrolysis and thermal dynamics of corncobs (CC) was investigated experimentally using the quantitative method of thermogravimetric analysis (TGA) coupled with mass spectrometry (MS), and the obtained results were compared in depth. For the examined heating rates of 5, 10, and 20 °C/min, the CC pyrolysis at higher heating rates resulted in a more complete decomposition. The initial pyrolysis temperature decreased when gas flow was increased from 30 to 90 mL/min, whereas the weight loss increased. Particle sizes (d ≤ 74 μm, 74 μm < d ≤ 154 μm, 154 μm < d ≤ 280 μm, and 280 μm < d ≤ 450 μm) had pronounced effects on the thermal decomposition and bio-syngas compounds (CO, CO2, CH4, and H2) distribution. The emission intensities of most the gaseous products increased at the elevated heating rate, while they decreased with increasing gas flow. In sum, the pyrolysis of CC particles of 154 μm < d ≤ 280 μm under 20 °C/min and in a gas flow of 30 to 60 mL/min was the most appropriate for bio-syngas production in industrial applications.
BibTeX
@inproceedings{yao2017assessing,
  author = {Xiwen Yao and Kaili Xu and Yu Liang},
  title = {{Assessing the Effects of Different Process Parameters on the Pyrolysis Behaviors and Thermal Dynamics of Corncob Fractions}},
  booktitle = {BioResources},
  year = {2017},
  doi = {10.15376/biores.12.2.2748-2767},
}
Figure