Analysis of UHF RFID CMOS rectifier structures and input impedance characteristics

Behnam Jamali, Damith C. Ranasinghe, Peter H. ColeProceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE 2005 · DOI

TL;DR

This paper explores novel rectifier structures for UHF RFID tags, focusing on improving power conversion efficiency and input impedance matching. By analyzing Schottky Barrier Diode (SBD) based voltage multipliers, the authors aim to enable more robust and cost-effective RFID solutions, crucial for widespread supply chain visibility.

What Problem Does This Paper Address?

Passive UHF RFID systems are revolutionizing logistics by providing supply chain visibility. However, their performance hinges on efficient power rectification and antenna-to-chip impedance matching, especially in the UHF ISM band. Existing solutions, often relying on MOSFET-based rectifiers, struggle with low input voltage levels and sluggish responses, limiting their effectiveness at greater distances from the reader. This paper addresses the need for improved rectifier designs that can efficiently convert weak RF signals into usable DC power for RFID tags, while also considering their impact on input impedance for optimal antenna matching.

Methods

The paper investigates a novel rectifier structure based on Silicon-Titanium Schottky Barrier Diodes (SBDs) integrated into a Dickson charge pump topology. This approach is contrasted with traditional MOSFET bridge rectifiers. The authors present an analytical model for the SBD-based voltage multiplier and analyze its performance characteristics, including output voltage, degradation features, and input impedance. They also discuss the trade-offs involved in capacitor selection for the charge pump and the impact of junction capacitance on output voltage.

Datasets

Not discussed in the paper.

Key Insights and Ideas

  • SBDs Offer a Low-Voltage Advantage: Schottky diodes exhibit a significantly lower voltage drop (around 200 mV) compared to MOSFETs, making them more suitable for rectifying weak RF signals commonly encountered in RFID applications, especially at the edge of the reader's range.
  • Dickson Charge Pump with SBDs: Integrating SBDs into a Dickson charge pump topology provides a promising avenue for achieving higher output voltages from low input RF power.
  • Input Impedance is Crucial for Matching: The input impedance of the rectifier structure is a critical factor for effective impedance matching with the RFID tag's antenna. The paper highlights that the number of stages in the charge pump directly influences this input impedance, with more stages generally leading to lower impedance.
  • Capacitor Selection is a Balancing Act: The choice of coupling and reservoir capacitors in the charge pump involves trade-offs. Smaller capacitors speed up charge transfer but can lead to higher losses, while larger capacitors can filter the input signal and increase RC time constants.
  • Optimum SBD Size is Key for Efficiency: Achieving high efficiency requires careful selection of SBDs. While larger SBDs offer higher saturation current and lower series resistance, they also have larger junction capacitances that can increase power loss and limit operating frequency.

Key Results

  • The paper proposes and analyzes a novel rectifier/multiplier topology using SBDs based on Dickson's design.
  • Simulations and analysis indicate that SBD-based rectifiers offer a more responsive and efficient solution for low input voltage scenarios compared to MOSFET bridge rectifiers.
  • The input impedance of the SBD-based charge pump is shown to decrease with an increasing number of stages.
  • Empirical measurements on commercial RFID chips are presented for comparison, showing input impedance values in the range of 6-154 Ω.

Limitations and Future Work

  • CMOS Integration Challenges: While the paper discusses SBDs, it notes that using SBD diodes in a standard CMOS circuit can lead to parasitic diode conduction issues (Dpn forward biasing) when the input voltage swings negative, similar to latch-up conditions. The proposed solution involves a specific circuit configuration to mitigate this.
  • Practical Realization: The paper mentions that a practical realization of the proposed concept is still in progress, with successful standard CMOS SBDs having been fabricated and tested.
  • Optimum SBD Size: The paper identifies the need to find an optimum size for SBDs to balance saturation current, series resistance, and parasitic capacitances for maximum efficiency.
  • Further Analysis of Charge Pump Performance: While analytical models are presented, further detailed analysis of charge pump performance under various load conditions and the impact of parasitic elements could be beneficial.

Summary updated

Abstract

Passive radio frequency identification (RFID) systems deployment efforts are revolutionizing supply chain logistics by providing unprecedented supply chain visibility. The widely used bandwidth of operation in modern systems is the UHF ISM (industrial, scientific, and medical) band. The performance of UHF RFID systems are largely reliant on low power CMOS circuits, efficient power rectification and the ability of RFID label antennas to match to the input impedance of the RFID label IC. This paper examines a new rectifying structure and considers it for its merits in RFID applications while analysing contribution of the rectifying structure to the input impedance of RFID chips as this is an important consideration in impedance matching to an external antenna.
BibTeX
@inproceedings{jamali2005analysis,
  author = {Behnam Jamali and Damith C. Ranasinghe and Peter H. Cole},
  title = {{Analysis of UHF RFID CMOS rectifier structures and input impedance characteristics}},
  booktitle = {Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE},
  year = {2005},
  doi = {10.1117/12.639592},
}

Loading related content...

Figure