Analysis of the Sensing Properties of a Highly Stable and Reproducible Ozone Gas Sensor Based on Amorphous In-Ga-Zn-O Thin Film

Chiu-Hsien Wu, Guo-Jhen Jiang, Kai-Wei Chang, Zu-Yin Deng, Yu-Ning Li, Kuen-Lin Chen, Chien-Chung JengSensors 2018 · OpenReview

TL;DR

This paper presents a highly stable and reproducible amorphous indium-gallium-zinc oxide (a-IGZO) thin film sensor for detecting ozone at ppb levels. The sensor demonstrates a linear response to ozone concentration and offers a faster detection method using the rate of resistance change, making it a promising candidate for practical ozone monitoring applications.

What Problem Does This Paper Address?

Accurate and reliable detection of ozone gas is crucial for environmental monitoring and industrial safety, as ozone can be harmful at elevated concentrations. Existing gas sensors often face challenges with sensitivity, stability, reproducibility, and response/recovery times, especially at low, environmentally relevant concentrations (parts per billion, ppb). This research aims to develop and characterize an a-IGZO thin film sensor that overcomes these limitations, offering a robust and sensitive solution for ppb-level ozone detection.

Methods

The researchers fabricated amorphous indium-gallium-zinc oxide (a-IGZO) thin films using RF sputtering. These films were deposited on glass substrates and then annealed. The sensing properties were investigated by exposing the films to varying ozone concentrations (500 ppb to 5 ppm) under continuous UV LED irradiation (365 nm). Key parameters measured and analyzed included:

  • Resistance-Time (R-T) curves: To observe the sensor's response and recovery behavior over time.
  • Resistance Change (ΔR) and Sensitivity (S): Quantifying the magnitude of the resistance shift and its relative change.
  • Response and Recovery Times (T90-res, T90-rec): Measuring the time taken to reach 90% of the full resistance change.
  • Time Constant (τ): Characterizing the exponential decay of the resistance.
  • Rate of Resistance Change (dR/dt): Analyzing the derivative of the resistance-time curve, a novel approach for faster detection.

The study also explored the effect of UV light intensity on the sensor's performance.

Datasets

Not discussed in the paper. The study relies on controlled laboratory experiments with generated ozone concentrations and measured resistance values.

Key Insights and Ideas

  • ppb-Level Detection Achieved: The a-IGZO sensor demonstrated a clear response to ozone concentrations as low as 60-70 ppb, indicating its potential for detecting harmful ozone levels.
  • Linearity is Key: Both the resistance change (ΔR) and sensitivity (S) showed a strong linear correlation with increasing ozone concentration, simplifying calibration and concentration determination.
  • Faster Detection via Rate of Change: Analyzing the rate of resistance change (dR/dt) proved to be a faster method for determining ozone concentration compared to traditional response/recovery times or time constants. This is because the maximum rate of change is directly proportional to the ozone concentration.
  • UV Light Enhances Performance: While the sensor works without UV, continuous UV irradiation significantly improved sensing speed and stability, particularly at low ozone concentrations. Higher UV intensity led to faster response and recovery.
  • Reproducibility is High: The sensor exhibited excellent stability and reproducibility over multiple test cycles, a critical factor for practical sensor applications.

Key Results

  • The a-IGZO thin film sensor successfully detected ozone concentrations ranging from 500 ppb to 5 ppm.
  • A good response was observed even at 60–70 ppb ozone.
  • Resistance change (ΔR) increased linearly from 17 MΩ at 0.5 ppm to 175 MΩ at 5 ppm.
  • Sensitivity (S) increased linearly from 1.4 at 0.5 ppm to 14 at 5 ppm.
  • Response times (T90-res) decreased from ~775 s at 0.5 ppm to ~210 s at 5 ppm, showing a first-order exponential decay.
  • Recovery times (T90-rec) also decreased from ~2470 s at 0.5 ppm to ~530 s at 5 ppm.
  • The time constant (τ) decreased with increasing ozone concentration, from ~324 s at 0.5 ppm to ~90 s at 5 ppm.
  • The maximum rate of resistance change (dR/dt) was found to be directly proportional to ozone concentration, with values ranging from ~45 KΩ/s at 0.5 ppm to ~1.5 MΩ/s at 5 ppm.
  • Higher UV light intensity (149.7 mW/cm²) resulted in faster response times (~110 s) compared to lower intensity (18.9 mW/cm², ~475 s) at 500 ppb ozone.

Limitations and Future Work

  • Low-Intensity Light Variance: The study notes that sensor sensitivity showed higher variance at low UV light intensity compared to high intensity, suggesting that high-intensity light is preferable for stable sensing, especially at low ozone concentrations.
  • Ozone Flow Stability: At low ozone concentrations, variations in ozone flow were observed to cause larger variances in response and recovery times, although resistance values remained stable.
  • Future Work: The paper suggests that a-IGZO thin films, combined with the first-order differentiation method for analyzing the rate of resistance change, are promising candidates for practical ozone sensors. Further optimization of deposition and operating conditions, particularly regarding light intensity, could enhance performance for specific applications. The ability to detect ozone at several ppb levels using the dR/dt method is highlighted as a significant advantage.

Summary updated

Abstract

In this study, the sensing properties of an amorphous indium gallium zinc oxide (a-IGZO) thin film at ozone concentrations from 500 to 5 ppm were investigated. The a-IGZO thin film showed very good reproducibility and stability over three test cycles. The ozone concentration of 60–70 ppb also showed a good response. The resistance change (ΔR) and sensitivity (S) were linearly dependent on the ozone concentration. The response time (T90-res), recovery time (T90-rec), and time constant (τ) showed first-order exponential decay with increasing ozone concentration. The resistance–time curve shows that the maximum resistance change rate (dRg/dt) is proportional to the ozone concentration during the adsorption. The results also show that it is better to sense rapidly and stably at a low ozone concentration using a high light intensity. The ozone concentration can be derived from the resistance change, sensitivity, response time, time constant (τ), and first derivative function of resistance. However, the time of the first derivative function of resistance is shorter than other parameters. The results show that a-IGZO thin films and the first-order differentiation method are promising candidates for use as ozone sensors for practical applications.
BibTeX
@inproceedings{wu2018analysis,
  author = {Chiu-Hsien Wu and Guo-Jhen Jiang and Kai-Wei Chang and Zu-Yin Deng and Yu-Ning Li and Kuen-Lin Chen and Chien-Chung Jeng},
  title = {{Analysis of the Sensing Properties of a Highly Stable and Reproducible Ozone Gas Sensor Based on Amorphous In-Ga-Zn-O Thin Film}},
  booktitle = {Sensors},
  year = {2018},
  url = {https://openreview.net/forum?id=Hai47OPz75DC},
}
Figure