Analysis of the Primary Constraint Conditions of an Efficient Photovoltaic-Thermoelectric Hybrid System

Guiqiang Li, Xiao Chen, Yi JinEnergies 2016 · DOI

TL;DR

This paper investigates the optimal design parameters for photovoltaic-thermoelectric (PV-TE) hybrid systems to maximize electrical efficiency. By developing a simulation model that accounts for temperature-dependent thermoelectric properties, the authors identify key constraints and relationships between geometric factors, solar irradiation, and cold-side temperature that dictate system performance, offering a guide for efficient PV-TEG design.

What Problem Does This Paper Address?

Solar energy conversion often involves a trade-off: photovoltaic (PV) cells directly convert sunlight to electricity, but their efficiency decreases with increasing temperature. Thermoelectric generators (TEGs) can convert waste heat into electricity, offering a way to utilize the infrared portion of the solar spectrum that PV cells miss. However, simply combining PV and TEG systems isn't straightforward. The heat generated by the PV cell, which is detrimental to its performance, is the very heat source needed by the TEG. This paper addresses the challenge of finding the optimal operating and design conditions for a PV-TE hybrid system to achieve higher overall electrical efficiency than a standalone PV system, by carefully analyzing the interplay between PV and TEG performance under various conditions.

Methods

The authors developed a simulation model for a PV-TEG hybrid system. This model incorporates temperature-dependent properties of the thermoelectric material (Bi₂Te₃), which is a crucial aspect often simplified in previous studies. The model analyzes the energy balance of the PV module and the heat transfer through the TEG. They then systematically investigated the impact of several key parameters on the overall system efficiency:

  • Geometric Parameters: TEG height (H) and cross-sectional area (S).
  • Solar Irradiation: Represented by the optical concentration ratio (C).
  • Cold Side Temperature (T_L): The temperature of the heat sink for the TEG.

To visualize and understand the constraint conditions for achieving an overall efficiency greater than 15% (a benchmark set against standard PV efficiency), the authors employed an "image area method." This method generates contour plots (yellow regions) that delineate the parameter space leading to efficient operation.

Datasets

Not discussed in the paper. The study relies on a simulation model and parameters derived from existing literature (cited in Table 1 and the References section).

Key Insights and Ideas

  • Temperature is a Double-Edged Sword: While heat is essential for TEG operation, excessive heat degrades PV performance. The model explicitly accounts for this trade-off.
  • Geometry Matters Significantly: There's a complex interplay between TEG height and cross-sectional area. Generally, a larger cross-sectional area and a lower height are favorable for higher overall efficiency, especially when other factors are constant.
  • The "Sweet Spot" for Efficiency: The study identifies specific parameter ranges (visualized by yellow regions in their plots) where the PV-TEG system significantly outperforms standard PV. Deviating from these ranges leads to diminished efficiency.
  • Optical Concentration Ratio Trade-off: While higher concentration ratios increase solar input, they can negatively impact the PV-TEG system's overall efficiency beyond a certain point, especially if not coupled with appropriate geometric design.
  • Cold Side Temperature is Critical: Lower cold-side temperatures are paramount for achieving high PV-TEG efficiency. As the cold-side temperature rises, the system's advantage over a standard PV system diminishes.

Key Results

  • The overall efficiency of the PV-TEG system is generally higher with a larger cross-sectional area (S) and a lower TEG height (H).
  • The study provides specific formulas for optimal TEG geometry:
  • For maximum efficiency: H₁ = 270S – 0.00011
    • For an overall efficiency of 15%: H₂ = 750S – 0.00048
  • The "yellow region" representing efficiencies above 15% becomes smaller as TEG height increases, indicating stricter constraint conditions. Conversely, the yellow region expands with increasing cross-sectional area, suggesting less strict constraints.
  • A higher optical concentration ratio generally leads to lower overall efficiency for the hybrid system, especially when the cross-sectional area is small or height is large.
  • The system's efficiency decreases significantly as the cold-side temperature increases. For example, with a cross-sectional area of 25 mm², the efficiency drops below 15% at temperatures above approximately 285 K.

Limitations and Future Work

  • Cost Considerations: The paper acknowledges that while larger cross-sectional areas and lower heights are beneficial for efficiency, practical applications often face cost constraints, leading to smaller TEG sizes and increased complexity in parameter coupling.
  • Simplified Assumptions: While temperature-dependent properties were included, some simplifications might still exist in the model (e.g., uniform temperature across PV and heat sink modules, 1D heat transfer).
  • Future Work: The authors suggest that their findings provide a benchmark for efficient PV-TEG design. Further research could explore more complex geometries, advanced thermoelectric materials, and real-world experimental validation to refine these optimal parameter ranges and address cost-effectiveness.

Summary updated

Abstract

Electrical efficiency can be increased by combining photovoltaic (PV) and the thermoelectric (TE) systems. However, a simple and cursory combination is unsuitable because the negative impact of temperature on PV may be greater than its positive impact on TE. This study analyzed the primary constraint conditions based on the hybrid system model consisting of a PV and a TE generator (TEG), which includes TE material with temperature-dependent properties. The influences of the geometric size, solar irradiation and cold side temperature on the hybrid system performance is discussed based on the simulation. Furthermore, the effective range of parameters is demonstrated using the image area method, and the change trend of the area with different parameters illustrates the constraint conditions of an efficient PV-TE hybrid system. These results provide a benchmark for efficient PV-TEG design.
BibTeX
@inproceedings{li2016analysis,
  author = {Guiqiang Li and Xiao Chen and Yi Jin},
  title = {{Analysis of the Primary Constraint Conditions of an Efficient Photovoltaic-Thermoelectric Hybrid System}},
  booktitle = {Energies},
  year = {2016},
  doi = {10.3390/en10010020},
}
Figure