An Autonomous Mobile Measurement Method for Key Feature Points in Complex Aircraft Assembly Scenes

Yang Zhang, Changyong Gao, Shouquan Sun, Xiao Guan, Yanjun Shi, Wei Liu, Yongkang LuMachines 2025 · DOI

TL;DR

This paper introduces an autonomous mobile measurement system for accurately capturing key feature points (KFPs) on large aircraft components. By intelligently planning measurement station locations, optimizing mobile robot paths, and automating measurement sequences, the system significantly reduces measurement errors and time compared to traditional manual methods.

What Problem Does This Paper Address?

Assembling large aircraft components requires precise alignment, which in turn relies on accurately measuring key feature points (KFPs) on these components. These KFPs are often numerous, widely distributed across large structures (up to 60 meters), and prone to line-of-sight occlusions. Traditional methods using laser trackers (LTs) require manual setup of multiple stations, often based on operator experience, leading to inefficiencies, potential errors, and significant time investment. The configuration of stations, the order of measurements, and the movement between stations are all manual processes that are difficult to automate and optimize, especially in complex, cluttered assembly environments. This paper aims to address these challenges by developing an autonomous system that can plan and execute KFP measurements efficiently and accurately.

Methods

The proposed method integrates several key components:

  • Optimal Measurement Station Planning: This involves determining the minimum number of LT stations, their ideal locations, and assigning specific KFPs to each station. The planning considers line-of-sight occlusion using a ray-triangle model and aims to minimize the total distance between stations and their assigned points, while adhering to LT operational constraints (e.g., vertical angle, distance).
  • Autonomous Mobile System Localization: The system uses a mobile laser tracker (MLT) mounted on an Automated Guided Vehicle (AGV). Localization is achieved through a hybrid approach combining radar-based coarse positioning and laser-based fine positioning. This allows the MLT to accurately determine its pose in the global coordinate system, crucial for precise measurements and navigation.
  • Fastest Motion Path Planning: The AGV's path planning considers not only obstacles but also the time cost associated with deceleration, stopping, and turning. An improved A* algorithm is used, with an evaluation function that prioritizes minimizing total operation time rather than just distance. This includes a turning time penalty to discourage unnecessary maneuvers.
  • Measurement Sequence Planning: For a given station, the system plans an optimal sequence for measuring multiple KFPs to minimize the total path length. This is achieved using an improved genetic algorithm that considers factors like mutation, crossover, and inversion to find efficient, non-overlapping measurement paths.

Datasets

Not discussed in the paper. The experiments were conducted on a simulated wing-to-fuselage assembly and a real-world wing-fuselage assembly experiment.

Key Insights and Ideas

  • Integrating Planning and Execution: The core innovation is the seamless integration of measurement planning (station layout, path planning, sequence planning) with autonomous execution by a mobile platform. This moves beyond static measurement setups.
  • Line-of-Sight as a Primary Constraint: Explicitly modeling and addressing line-of-sight occlusion during station planning is critical for ensuring complete coverage in complex environments.
  • Time-Optimized Path Planning: Prioritizing operational time over pure distance in path planning is crucial for efficiency in dynamic assembly scenarios, especially when considering the overhead of AGV maneuvers.
  • Hybrid Localization for Robustness: Combining coarse and fine localization methods provides a robust way to determine the mobile system's position and orientation, essential for accurate measurements.
  • Genetic Algorithm for Sequence Optimization: Using a genetic algorithm for measurement sequence planning effectively tackles the combinatorial complexity of finding optimal paths for multiple points at a single station.

Key Results

  • Reduced Measurement Error: The proposed station planning method reduced the average measurement error from 0.035 mm (empirical method) to 0.022 mm, a 37% decrease.
  • Significant Time Reduction: The overall measurement time was cut from one hour to within 25 minutes, representing a reduction of over 50%.
  • Optimized Measurement Paths: The optimized measurement sequence resulted in total distances of 12,261.601 mm, compared to 16,005.305 mm before optimization, with paths that neither overlap nor intersect.

Limitations and Future Work

  • Multi-Device Coordination: The current work focuses on a single mobile measurement system. The authors acknowledge that in some aircraft assembly scenarios, multiple instruments might be deployed simultaneously to further improve efficiency.
  • Future Work: Future research will focus on the optimal scheduling of a fleet of mobile measuring devices and the development of a fully automated "measurement-planning-control" software platform to enhance measurement efficiency in aircraft assembly.

Summary updated

Abstract

Large-scale measurement of key feature points (KFPs) on an aircraft is essential for coordinated movement of locators, which is critical to the final assembly accuracy. Due to the large number and wide distribution of KFPs as well as line-of-sight occlusion, network measurement of laser trackers (LTs) is required. Existing approaches rely on operational experience for the configuration of stations, sequences and station transitions of LTs, which compromises both efficiency and automation capability. To tackle this challenge, this article presents an autonomous mobile measurement method for KFPs in complex scenes of aircraft assembly, incorporating path self-planning and self-positioning capabilities, thereby substantially diminishing temporal expenditure. Firstly, a simultaneous self-planning method of measurement stations and tasks is proposed to determine the minimum number of stations, optimal locations, and their specific KFPs at each station. Secondly, considering obstacles and turning time, a path planning model of mobile LTs combining coarse and fine localization is established to realize automatic station transitions. Finally, an optimal sequence of series of KFPs with a wide spatial distribution is generated to minimize total distance. Aircraft component assembly experiments validated the method, cutting measurement error by 37% and total measurement time by over 50%.
BibTeX
@inproceedings{zhang2025autonomous,
  author = {Yang Zhang and Changyong Gao and Shouquan Sun and Xiao Guan and Yanjun Shi and Wei Liu and Yongkang Lu},
  title = {{An Autonomous Mobile Measurement Method for Key Feature Points in Complex Aircraft Assembly Scenes}},
  booktitle = {Machines},
  year = {2025},
  doi = {10.3390/machines13100892},
}
Figure