An Aerospace Layering Time Synchronization Architecture and Intersatellite Microwave Links Performance Analysis Based on 3-Layer Satellite Networks

Feijiang Huang, Xiaochun Lu, Guangcan Liu, Tao Han, Cheng Fang, Feng LiuResearch 2013 · DOI

Abstract

The appropriate high-accuracy time and frequency standard is basic to normal operation of various kinds of aerospace application systems, which influences systems performance. The study of establishing suitable time and frequency standard and intersatellite performance analysis in aerospace is very important. Based on the establishment of aerospace satellite visual model, the simulation of satellite visual time on 3-layer satellite networks, including GEO satellite (Geostationary Earth Orbit), IGSO (Inclined Geosynchronous Orbit) satellites and MEO (Medium Earth Orbit) satellites, has been conducted. The visual features of this satellite network have been gained. Combining with the major influencing factors of satellite clock correction error, aerospace time synchronization architecture on the basis of layering has been proposed. Furthermore, intersatellite links performance analysis is the basis for establishing aerospace layering time synchronization architecture. The 3-layer satellite networks is used as an example to simulate the variation range of distance interlayer satellites of the 3-layer satellite networks and to analyze the performance of GEO-IGSO, GEO-MEO and IGSO-MEO links in S-band and Ka-band under the preset intersatellite transmission system, link parameters, transmission loss and without regard to the error of the intersatellite pointing accuracy. The results show that at the maximum intersatellite distance, if the S-band transmission rate is in excess of 2 Mbps, when the antenna is 1 m in diameter, the transmitting power needed is about 50 W. In the Ka-band, 1m antennas only need 1 W transmitting power to provide an intersatellite data transmission rate higher than 2 Mbps. The Ka-band is more favorable for improving the performance of intersatellite links of 3-layer satellite networks. Research results serves as reference for the establishment of aerospace layering time synchronization architecture based on 3-layer satellite networks.

Introduction

Precise time synchronization is the "heartbeat" of modern aerospace applications, from deep space exploration to distributed satellite swarms. Traditionally, spacecraft synchronize clocks independently with ground stations. However, this method suffers from low accuracy due to short synchronization windows, vulnerability to ground station failure, and increasing complexity as orbital networks expand. This paper proposes a robust, space-based synchronization architecture where satellites maintain synchronization autonomously across multiple orbital layers.

Proposed Layered Architecture and Methods

The researchers propose a hierarchical "layering" architecture utilizing three distinct orbital layers: Geostationary Earth Orbit (GEO), Inclined Geosynchronous Orbit (IGSO), and Medium Earth Orbit (MEO).

The 3-layer satellite network architecture consisting of GEO, IGSO, and MEO satellites.

In this hierarchy, GEO satellites—the most stable in position—act as the primary time source (master clocks), transmitting timing signals to the IGSO and MEO layers. To validate this, the researchers used Satellite Tool Kit (STK) to simulate a constellation of 3 GEO, 3 IGSO, and 7 MEO satellites. They established a mathematical "visual model" to determine inter-satellite visibility and analyzed link performance using the Friis transmission equation to compare S-band (2.4 GHz) and Ka-band (30 GHz) microwave links.

Results and Performance Analysis

Visibility and Synchronization

Simulations revealed high visibility rates: GEO and IGSO layers maintain 100% continuous visibility, while GEO-to-MEO visibility exceeds 97%. This high "uptime" minimizes clock correction extrapolation errors, as satellites can frequently reference the master GEO clocks.

The study mapped the significant variation in intersatellite distances over time. Links can range from a few hundred to tens of thousands of kilometers, necessitating robust automatic power control and tracking capabilities.

Variation of intersatellite distances between different orbital layers (GEO-IGSO, GEO-MEO, and IGSO-MEO) over time.

Frequency Band Comparison

The quantitative comparison between S-band and Ka-band links highlighted a major efficiency gap. To achieve a 2 Mbps data rate at maximum distance with a 1-meter antenna:

  • S-band requires approximately 50W of transmitting power.
  • Ka-band requires only 1W.

Ka-band's higher frequency allows for narrower beams and higher gain, enabling higher data rates with significantly lower power consumption, which is critical for sub-nanosecond time synchronization.

Conclusion

The proposed layered architecture and the transition to Ka-band microwave links offer a path toward high-accuracy, autonomous aerospace timing. While Ka-band provides superior power efficiency and throughput, it introduces challenges in pointing accuracy and hardware complexity. Future work will address these technical hurdles to realize fully autonomous, resilient space-based timing networks.

Summary updated

Abstract

The appropriate high-accuracy time and frequency standard is basic to normal operation of various kinds of aerospace application systems, which influences systems performance. The study of establishing suitable time and frequency standard and intersatellite performance analysis in aerospace is very important. Based on the establishment of aerospace satellite visual model, the simulation of satellite visual time on 3-layer satellite networks, including GEO satellite (Geostationary Earth Orbit), IGSO (Inclined Geosynchronous Orbit) satellites and MEO (Medium Earth Orbit) satellites, has been conducted. The visual features of this satellite network have been gained. Combining with the major influencing factors of satellite clock correction error, aerospace time synchronization architecture on the basis of layering has been proposed. Furthermore, intersatellite links performance analysis is the basis for establishing aerospace layering time synchronization architecture. The 3-layer satellite networks is used as an example to simulate the variation range of distance interlayer satellites of the 3-layer satellite networks and to analyze the performance of GEO-IGSO, GEO-MEO and IGSO-MEO links in S-band and Ka-band under the preset intersatellite transmission system, link parameters, transmission loss and without regard to the error of the intersatellite pointing accuracy. The results show that at the maximum intersatellite distance, if the S-band transmission rate is in excess of 2 Mbps, when the antenna is 1 m in diameter, the transmitting power needed is about 50 W. In the Ka-band, 1m antennas only need 1 W transmitting power to provide an intersatellite data transmission rate higher than 2 Mbps. The Ka-band is more favorable for improving the performance of intersatellite links of 3-layer satellite networks. Research results serves as reference for the establishment of aerospace layering time synchronization architecture based on 3-layer satellite networks.
BibTeX
@inproceedings{huang2013aerospace,
  author = {Feijiang Huang and Xiaochun Lu and Guangcan Liu and Tao Han and Cheng Fang and Feng Liu},
  title = {{An Aerospace Layering Time Synchronization Architecture and Intersatellite Microwave Links Performance Analysis Based on 3-Layer Satellite Networks}},
  booktitle = {Research},
  year = {2013},
  doi = {10.19026/rjaset.5.4671},
}
Figure