Aggregating Buildings as Virtual Power Plant: Architecture, Implementation Technologies, and Case Studies

Fengji Luo, Ali Dorri, Gianluca Ranzi, Raja JurdakarXiv 2020 · DOI · arXiv

Abstract

The prevalence of distributed generation drives the emergence of the Virtual Power Plant (VPP) paradigm. A VPP aggregates distributed energy resources while operating as a conventional power plant. In recent years, several renewable energy sources have been installed in the commercial/industrial/residential building sector and they lend themselves for possible aggregation within the VPP operations. At present, building-side energy resources are usually managed by building energy management systems (BEMSs) with autonomous objectives and policies, and they are usually not setup to be directly controlled for the implementation of a VPP energy management system. This article presents a Building VPP (BVPP) architecture that aggregates building-side energy resources through the communication between the VPP energy management system and autonomous BEMSs. The implementation technologies, key components, and operation modes of BVPPs are discussed. Case studies are reported to demonstrate the effectiveness of BVPP in different operational conditions.

Introduction

The traditional electrical grid is undergoing a paradigm shift from a top-down, vertical structure to a distributed model. This transition is driven by the proliferation of Distributed Energy Resources (DERs)—such as rooftop solar, electric vehicles, and residential batteries—scattered across the distribution network. The "Virtual Power Plant" (VPP) concept was created to aggregate these small resources so they can act as a single conventional power plant.

However, a significant technical hurdle exists: most modern buildings already possess their own "brains" in the form of Building Energy Management Systems (BEMS). These systems operate with local goals, such as occupant comfort and bill minimization, and are not designed to take direct orders from a third-party grid operator. This paper addresses this "control conflict" by proposing a Building VPP (BVPP) architecture where the VPP collaborates with existing BEMS rather than overriding them.

The BVPP Architecture

The core innovation of this research is a decomposed, loosely coupled architecture. Instead of a central VPP Energy Management System (EMS) micro-managing every individual device, the workflow is split between global and local agents.

The Proposed BVPP Architecture: A decomposed model for coordinating autonomous building energy systems with the macro grid via cloud infrastructure and IoT gateways.

As illustrated in the architecture, the BVPP EMS handles global optimization, market bidding, and grid signals within a cloud infrastructure. The BEMS acts as a local agent, receiving high-level instructions from the BVPP and determining how to meet them while respecting the building owner's preferences and local constraints. This model preserves user privacy and local autonomy, which are major barriers to adoption in traditional VPP frameworks.

Enabling Technologies

Several key technologies facilitate the implementation of the BVPP:

  • Non-Intrusive Appliance Load Monitoring (NILM): This allows the system to disaggregate total power consumption into individual appliance loads without requiring sensors on every plug.
  • Blockchain: Used to create a trusted environment for transactions and commitments between participants who may not have prior relationships.
  • Fuzzy C-Means (FCM) Clustering: Employed in the occupant-centric model to group households with similar lifestyles and identify those with inefficient energy habits.

Operational Modes

The paper defines three distinct ways a BVPP can function:

  1. Technical (T-BVPP): Focuses on grid stability, including frequency regulation and peak shaving.
  2. Commercial (C-BVPP): Focuses on profit by aggregating small solar outputs to meet the capacity barriers required for wholesale energy market participation.
  3. Occupant-Centric (O-BVPP): A social approach where the system identifies "peers" with similar lifestyles and recommends energy-saving schedules based on successful strategies used by others.

Case Studies and Results

The researchers validated the architecture using "SimHouse," a residential power load generator that maps lifestyle models to physical appliance simulations.

Case 1: Market Participation

In a simulation of 50 buildings with a shared battery, the BVPP successfully sold energy back to the grid. The simulation resulted in $340.20 in total revenue, split between the BVPP operator ($165.40) and the building owners ($174.80), demonstrating a viable economic incentive for participation.

Case 2: Knowledge Sharing

By clustering 500 households, the system identified 171 "inefficient" users. By recommending energy-usage plans based on their more efficient "peers," the system achieved significant savings.

Occupant-Centric Knowledge Sharing: Recommended usage plans for shiftable appliances based on peer lifestyle similarity and time-of-use rates.

As shown in the figure, the system provides specific recommendations for shifting appliances like dishwashers and washing machines to off-peak hours. In this case study, the system achieved a total saving of $188.10 for a single month, averaging $1.10 per household, simply through optimized scheduling.

Conclusion and Future Work

The BVPP architecture offers a robust framework for turning buildings from passive "energy takers" into active "energy providers." While the results are promising, future work must address the computational complexity of scaling to city-wide deployments and the challenges of ensuring user compliance with behavioral recommendations. Additionally, the practical implementation of secure, low-latency communication across thousands of buildings remains a critical area for further exploration.

Summary updated

Abstract

The prevalence of distributed generation drives the emergence of the Virtual Power Plant (VPP) paradigm. A VPP aggregates distributed energy resources while operating as a conventional power plant. In recent years, several renewable energy sources have been installed in the commercial/industrial/residential building sector and they lend themselves for possible aggregation within the VPP operations. At present, building-side energy resources are usually managed by building energy management systems (BEMSs) with autonomous objectives and policies, and they are usually not setup to be directly controlled for the implementation of a VPP energy management system. This article presents a Building VPP (BVPP) architecture that aggregates building-side energy resources through the communication between the VPP energy management system and autonomous BEMSs. The implementation technologies, key components, and operation modes of BVPPs are discussed. Case studies are reported to demonstrate the effectiveness of BVPP in different operational conditions.
BibTeX
@misc{luo2020aggregating,
  author = {Fengji Luo and Ali Dorri and Gianluca Ranzi and Raja Jurdak},
  title = {{Aggregating Buildings as Virtual Power Plant: Architecture, Implementation Technologies, and Case Studies}},
  year = {2020},
  eprint = {2004.05807},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/2004.05807},
}
Figure