AEROBULL: A Center-of-Mass displacing aerial vehicle enabling efficient high-force interaction

Tong Hui, Stefan Rucareanu, Esteban Zamora, Simone D'Angelo, Haotian Liu, Matteo FumagalliRobotics Auton. Syst 2025 · DOI

TL;DR

This paper introduces AEROBULL, a novel aerial vehicle designed for efficient, high-force interaction with non-horizontal surfaces. By incorporating tiltable rotors and a unique shifting-mass mechanism to dynamically adjust its center of mass, AEROBULL can exert forces comparable to its own weight, overcoming limitations of traditional aerial robots in industrial inspection and maintenance tasks.

What Problem Does This Paper Address?

Industrial inspection and maintenance tasks, especially in hard-to-reach areas, often require significant force application and stable contact with surfaces. Traditional methods using human workers are costly, unsafe, and limited in accessibility. While Unmanned Aerial Vehicles (UAVs) offer a promising alternative, existing multirotor platforms struggle to exert substantial forces, particularly on non-horizontal surfaces. This is due to their inherent underactuation, where gravity compensation and force generation are coupled, and the limitations imposed by a fixed center of mass (CoM). Mounting manipulators on UAVs can increase complexity and weight. This paper addresses the need for an aerial platform that can efficiently generate high forces for tasks like pushing on vertical surfaces, while maintaining stability and maneuverability.

Methods

The AEROBULL platform features two key innovations:

  • Tiltable Back Rotors: Four rotors at the rear of the vehicle can tilt, allowing for thrust vectoring. This enables the platform to generate forces in directions other than directly downwards, crucial for interacting with non-horizontal surfaces.
  • Shifting-Mass Mechanism: A movable plate within the vehicle's body can dynamically shift its CoM along the longitudinal axis. This mechanism is driven by a servo motor and a lead screw, allowing for precise and slow adjustments. The goal is to move the CoM closer to the work surface during interaction, thereby increasing the effective pushing force and reducing destabilizing torques.

The control framework is a cascade of low-level geometric attitude control and high-level selective impedance control. The impedance controller allows the system to track desired forces and positions, while the attitude controller ensures stable flight. A control allocation module translates these desired actions into commands for the rotors' speeds and the tilting angle of the back rotors. The system's dynamics are modeled, considering the influence of the shifting mass on the inertia matrix.

Datasets

Not discussed in the paper. The experiments were conducted using the developed physical prototype and an indoor environment with an OptiTrack system for pose tracking.

Key Insights and Ideas

  • CoM Displacement is Key for High-Force Interaction: The most significant insight is that dynamically shifting the CoM towards the interaction surface dramatically enhances the achievable pushing force. This is demonstrated by comparing experiments with and without CoM displacement.
  • Synergy of Tiltable Rotors and CoM Shift: The combination of tiltable rotors for directional thrust and CoM displacement for force amplification creates a powerful system for contact-based tasks.
  • Efficient Force Generation: The platform achieves high pushing forces (up to 28N) with a relatively low total mass (3.12kg), making it energy-efficient compared to solutions that might rely on heavier manipulators.
  • Reduced Oscillations with Displaced CoM: Experiments showed that when the CoM was shifted, the platform exhibited fewer oscillations during pushing tasks compared to a fixed CoM configuration.

Key Results

  • The AEROBULL platform, with a total mass of 3.12kg, achieved a maximum pushing force of 28N on a vertical surface. This force is nearly equal to the vehicle's own gravity force (30.5N).
  • In experiments with the CoM shifted towards the work surface (Case 1), the platform generated approximately 19N at a setpoint 0.8m behind the surface, 23N at 1.0m, and 28N at 1.2m.
  • In contrast, when the CoM was fixed (Case 2), the platform struggled to maintain stable contact and exhibited significant oscillations, with pushing forces around 10-13N at smaller setpoints and an unstable impulse of 20N at a larger setpoint before the experiment was terminated.
  • The back rotors' speed increased significantly (up to 0.9 of maximum) when exerting higher forces with CoM displacement, while front rotors' speeds decreased.

Limitations and Future Work

Limitations:

  • The paper notes that if the CoM is displaced too far beyond a certain limit (d > L), the aerial vehicle can flip, leading to instability. The CoM displacement was therefore restricted to avoid such scenarios.
  • The experiments were conducted in a controlled indoor environment.
  • While the system achieved high forces, the pitch and yaw errors increased when larger pushing distances (op) were commanded.

Future Work:

  • The authors suggest that the platform's design and control framework provide a foundation for developing future custom aerial manipulation applications.
  • The paper highlights promising future revenue in enhancing high-force tool manipulation with aerial vehicles in industrial applications.
  • Further research could explore more complex interaction tasks and environments.

Summary updated

BibTeX
@article{hui2025aerobull,
  author = {Tong Hui and Stefan Rucareanu and Esteban Zamora and Simone D'Angelo and Haotian Liu and Matteo Fumagalli},
  title = {{AEROBULL: A Center-of-Mass displacing aerial vehicle enabling efficient high-force interaction}},
  journal = {Robotics Auton. Syst.},
  year = {2025},
  doi = {10.1016/j.robot.2025.105127},
}
Figure