Adsorption Characteristics of Phosphate Based on Al-Doped Waste Ceramsite: Batch and Column Experiments

Yameng Ma, Jia Zhu, Jianghua Yu, Yicheng Fu, Chao Gong, Xiao HuangInternational Journal of Environmental Research and Public Health 2022 · DOI

TL;DR

This study introduces Al-doped waste ceramsite (Al-ceramsite), synthesized from industrial byproducts like sludge, cement blocks, and coal fly ash, as a highly effective adsorbent for phosphate removal from water. The material demonstrates excellent performance in both batch and column experiments, achieving near-complete removal of phosphate from actual rainwater and meeting stringent environmental standards.

What Problem Does This Paper Address?

Excessive phosphorus in water bodies, primarily from agricultural runoff and wastewater, leads to significant environmental issues like eutrophication and algal blooms. While various phosphorus removal methods exist, adsorption is favored for its simplicity and efficiency. However, many existing adsorbents are costly or difficult to produce sustainably. This paper addresses the need for a low-cost, high-performance adsorbent derived from industrial waste for effective phosphate removal, particularly in the context of rainwater purification.

Methods

The researchers synthesized Al-ceramsite by doping a pre-formed ceramsite (made from sludge, cement blocks, and coal fly ash) with aluminum nitrate solution. They then conducted:

  • Batch Adsorption Experiments: To optimize removal conditions, they systematically varied parameters such as Al-ceramsite dosage, initial phosphate concentration, temperature, and initial pH. The effect of coexisting ions (cations and anions) was also investigated.
  • Desorption Experiments: To assess the regenerability of the Al-ceramsite, they studied the influence of pH and different desorbent types (sodium acetate, sodium carbonate, and sodium hydroxide) and concentrations on phosphate release.
  • Dynamic Adsorption Column Experiments: To simulate real-world conditions, they used Al-ceramsite packed in PVC columns to treat actual rainwater. They investigated the impact of submerged zone depth (SZD), filter media height (FMH), influent flow rate, and antecedent dry days (ADD) on phosphate removal efficiency.
  • X-ray Photoelectron Spectroscopy (XPS): This technique was employed to analyze the surface elemental composition and chemical states of the ceramsite before and after phosphate adsorption, providing insights into the adsorption mechanism.

Datasets

Not discussed in the paper. The study utilized synthetic phosphate solutions and collected natural rainwater for experiments.

Key Insights and Ideas

  • Waste Valorization for Environmental Solutions: The study highlights the potential of transforming industrial waste materials (sludge, cement, fly ash) into valuable adsorbents, offering a dual benefit of waste management and water purification.
  • Synergistic Effect of Aluminum Doping: Doping the waste ceramsite with aluminum significantly enhanced its phosphate adsorption capacity compared to the undoped version, suggesting a crucial role for aluminum in the adsorption mechanism.
  • Optimal Conditions for High Efficiency: The research identified specific optimal conditions for Al-ceramsite, including a dosage of 40 g/L, initial phosphate concentration of 10 mg/L, a temperature of 25 °C, and a pH of 5, leading to high removal efficiencies.
  • Robust Performance in Real Rainwater: The Al-ceramsite demonstrated remarkable effectiveness in removing phosphate from actual rainwater in column experiments, achieving complete removal and meeting stringent environmental standards (Class I surface water quality, < 0.02 mg/L).
  • Ligand Exchange as the Primary Mechanism: XPS analysis strongly indicated that ligand exchange and complexation between phosphate ions and aluminum on the ceramsite surface are the dominant mechanisms for phosphate removal.
  • Alkaline Environment Favors Desorption: While acidic conditions are optimal for adsorption, an alkaline environment (pH 10) was found to be most effective for desorbing phosphate from the Al-ceramsite, suggesting good regenerability.

Key Results

  • Batch Adsorption:
    • Al-ceramsite achieved a maximum removal efficiency of 92.81% under optimal conditions (40 g/L dosage, 10 mg/L initial PO₄³⁻-P, 25 °C, pH 5).
  • The adsorption capacity increased with initial phosphate concentration, reaching up to 274.68 mg/kg at 10 mg/L.
  • The optimal pH for adsorption was 5, with efficiency dropping significantly at higher pH values.
  • Cations (Ca²⁺, Mg²⁺) showed a facilitating effect on adsorption, while anions (SO₄²⁻, CO₃²⁻, F⁻, Cl⁻) inhibited it, with F⁻ being the most inhibitory.
  • Desorption:
    • Alkaline conditions (pH 10) significantly enhanced phosphate desorption.
  • NaOH was the most effective desorbent, with a desorption rate of 70% achieved at 1 mol/L NaOH concentration.
  • Column Experiments:
    • Complete removal of PO₄³⁻-P from actual rainwater was achieved.
  • Effluent PO₄³⁻-P concentrations were consistently below environmental quality standards for surface water Class I (< 0.02 mg/L).
  • Optimal submerged zone depth (SZD) was 5 cm, and optimal filter media height (FMH) was 15 cm.
  • The Al-ceramsite column showed resilience to varying influent flow rates and antecedent dry days, indicating practical applicability.

Limitations and Future Work

  • Limitations:
    • While Al-ceramsite showed good desorption, the study notes that some PO₄³⁻-P adsorption might be irreversible chemisorption, potentially limiting complete regeneration.
  • The study focused on the chemical aspects of adsorption; the interactions of micro-organisms within the column were not deeply explored.
  • Future Work:
    • Further investigation into the interactions of micro-organisms within the Al-ceramsite column is suggested to deepen the understanding of PO₄³⁻-P removal.
  • Exploring the long-term stability and performance of Al-ceramsite in continuous flow systems under varying environmental conditions would be beneficial.
  • Investigating the potential for recovering phosphorus from the desorption solution could add further value.

Summary updated

Abstract

Phosphorus widely existing in rainfall and wastewater impacts the water environment. In this study, sludge, cement block, and coal fly ash were employed as ceramsite material to synthesize Al-doped waste ceramsite (Al-ceramsite) for removing phosphate (PO<sub>4</sub><sup>3-</sup>-P) from aqueous solutions. Batch static adsorption-desorption experiments were designed to investigate the effect of various parameters such as Al-ceramsite dosage, PO<sub>4</sub><sup>3-</sup>-P concentration, temperature, initial pH, coexisting ions, and desorbents on the removal of PO<sub>4</sub><sup>3-</sup>-P. Also, the fate of PO<sub>4</sub><sup>3-</sup>-P removal efficiency in actual rainwater was studied through dynamic adsorption column experiments using Al-ceramsite. Results showed that Al-ceramsite could remove PO<sub>4</sub><sup>3-</sup>-P efficiently under the optimum parameters as follows: Al-ceramsite dosage of 40 g/L, initial PO<sub>4</sub><sup>3-</sup>-P concentration of 10 mg/L, temperature of 25 °C, and pH of 5. Besides that, the Al-ceramsite could completely remove PO<sub>4</sub><sup>3-</sup>-P in actual rainwater, and the effluent PO<sub>4</sub><sup>3-</sup>-P concentration was lower than the environmental quality standards for surface water Class Ⅰ (0.02 mg/L). The adsorption characteristics of Al-ceramsite on PO<sub>4</sub><sup>3-</sup>-P by X-ray photoelectron spectroscopy (XPS) were further explained. As a result, ligand exchange and complexation were confirmed as the main PO<sub>4</sub><sup>3-</sup>-P removal mechanism of Al-ceramsite. Thus, Al-ceramsite was prepared from industrial waste and has shown excellent potential for phosphorus removal in practical applications.
BibTeX
@article{ma2022adsorption,
  author = {Yameng Ma and Jia Zhu and Jianghua Yu and Yicheng Fu and Chao Gong and Xiao Huang},
  title = {{Adsorption Characteristics of Phosphate Based on Al-Doped Waste Ceramsite: Batch and Column Experiments}},
  journal = {International Journal of Environmental Research and Public Health},
  year = {2022},
  doi = {10.3390/ijerph20010671},
}
Figure