A Wideband Variable Gain Amplifier Design for 60GHz Millimeter-wave Receiver

Yue Wu, Zhiqun Li, Qin Li, Zhigong WangAdvances 2013 · DOI

Abstract

This paper presents a wideband variable gain amplifier (VGA) applied to 60GHz millimeter-wave receiver with an operating frequency from DC to 1.08GHz and variable gain range from 0dB to 60dB. The entire VGA consists of an 8dB fixed gain stage, a 0~48dB coarse gain control stage, a 0~12dB fine gain control stage and an output buffer stage. Both the coarse gain control stage and the fine gain control stage adopt open loop amplifier with local feedback. The feedback capacitors are added to compensate the bandwidth of the circuit. The VGA circuit is designed in TSMC 65nm CMOS process. The post simulation results show that: the operating current of the entire VGA with testing buffer is 20mA. The 3dB bandwidth is larger than 1.4GHz. The OP 1dB at 0dB gain is 0 dBm. The whole chip area is 1.5 × 0.6 mm².

Introduction

In 60GHz wireless communication systems, signal strength fluctuates significantly due to atmospheric absorption and physical obstacles. To ensure reliable data processing, receivers must provide a constant signal amplitude to the Analog-to-Digital Converter (ADC). This necessitates a Variable Gain Amplifier (VGA) with a wide gain range and high bandwidth. Traditional closed-loop architectures often struggle with bandwidth-gain trade-offs at millimeter-wave frequencies. This work addresses these challenges using a multi-stage open-loop design with local feedback in 65nm CMOS.

System Architecture

The proposed VGA architecture is partitioned into four distinct sections to achieve a high dynamic range with precise control. As shown in Figure 1, the chain begins with an 8dB fixed gain stage to compensate for initial losses. This is followed by a coarse gain control stage providing 0–48dB in 12dB increments, and a fine gain control stage offering 0–12dB in 2dB steps. An output buffer completes the chain to drive subsequent stages.

Block diagram of the multi-stage VGA architecture.

Circuit Design and Implementation

The design utilizes open-loop amplifiers with local feedback (source degeneration) instead of global feedback loops. This choice enhances bandwidth by reducing load capacitance and avoiding stability issues common in high-gain operational amplifiers. The gain is primarily determined by the ratio of the load resistor ($R_L$) to the degeneration resistor ($R_s$), ensuring predictable performance across process variations.

To maintain a flat frequency response up to 1.08GHz, feedback capacitors ($C_s$) are integrated in parallel with the degeneration resistors. This "peaking" technique compensates for the natural high-frequency roll-off of the transistors, extending the 3dB bandwidth to over 1.4GHz. Each stage is AC-coupled to prevent DC offset propagation, which could otherwise saturate the high-gain stages.

Results and Discussion

The VGA was designed and simulated using the TSMC 65nm CMOS process. Post-layout simulations, which include parasitic effects, confirm a linear-in-dB gain characteristic across the full control range.

Simulated gain versus digital control word, demonstrating a 60dB range.

Key performance metrics include:

  • Gain Range: 0dB to 60dB with ~2dB resolution.
  • Bandwidth: >1.4 GHz, comfortably exceeding the 1.08GHz requirement.
  • Power Consumption: 24mW (20mA at 1.2V supply).
  • Linearity: Output 1dB compression point (OP1dB) of 0dBm at 0dB gain.
  • Noise Figure: Below 16.6dB from 10MHz to 1.08GHz.
  • Compact Size: Total chip area of 0.9 mm² (1.5mm × 0.6mm).

While the open-loop structure provides superior speed, it is inherently more sensitive to absolute gain accuracy than closed-loop designs. Additionally, flicker noise increases the noise figure at frequencies below 10MHz, though this is less critical for the intended wideband applications.

Conclusion

A high-performance wideband VGA for 60GHz receivers has been demonstrated. By employing a multi-stage open-loop architecture with local feedback and capacitive compensation, the design achieves a 60dB gain range and 1.4GHz bandwidth with low power consumption. Future work will involve silicon characterization to validate these post-simulation results against real-world environmental and packaging effects.

Summary updated

Abstract

This paper presents a wideband variable gain amplifier (VGA) applied to 60GHz millimeter-wave receiver with an operating frequency from DC to 1.08GHz and variable gain range from 0dB to 60dB. The entire VGA consists of an 8dB fixed gain stage, a 0~48dB coarse gain control stage, a 0~12dB fine gain control stage and an output buffer stage. Both the coarse gain control stage and the fine gain control stage adopt open loop amplifier with local feedback. The feedback capacitors are added to compensate the bandwidth of the circuit. The VGA circuit is designed in TSMC 65nm CMOS process. The post simulation results show that: the operating current of the entire VGAwith testing buffer is 20mA. The 3dB bandwidth is larger than 1.4GHz. The OP 1dB at 0dB gain is 0 dBm. The whole chip area is 1.50.6mm 2 .
BibTeX
@inproceedings{wu2013wideband,
  author = {Yue Wu and Zhiqun Li and Qin Li and Zhigong Wang},
  title = {{A Wideband Variable Gain Amplifier Design for 60GHz Millimeter-wave Receiver}},
  booktitle = {Advances},
  year = {2013},
  doi = {10.2991/icmt-13.2013.143},
}
Figure