A terminal sliding mode based torque distribution control for an individual-wheel-drive vehicle

Pan Song, Changfu Zong, Masayoshi TomizukaJournal of Zhejiang University. Science A 2014 · DOI

Abstract

This paper presents a torque distribution method for an individual-wheel drive vehicle, in which each wheel is controlled individually by its own electric motor. The terminal sliding mode technique is employed for the motion control so as to track the desired vehicle motion obtained by interpreting the driver's commands. Thus, finite-time convergence of the system's dynamic errors can be achieved on the terminal sliding manifolds, as compared to the well-used linear sliding surface. By considering nonlinear constraints of the tire adhesive limits, a simple yet effective distribution strategy is introduced to allocate the motion control efforts to each of the four wheels. Through the use of a high-fidelity CarSim full-vehicle model, vehicle stability and handling performance of the proposed controller is evaluated in both open-and closed-loop simulations.

Introduction

Individual-wheel-drive (IWD) electric vehicles offer significant advantages for Global Chassis Control (GCC) due to the independent controllability of each wheel's torque. However, this flexibility introduces complex control challenges. Specifically, motion control must accurately translate driver intent into total forces and moments, while control allocation must distribute these efforts across four wheels without exceeding physical tire grip limits. Traditional Sliding Mode Control (SMC) provides robustness but typically only guarantees asymptotic convergence, meaning errors diminish over "infinite" time. In high-speed automotive applications, faster, finite-time convergence is critical for safety.

Proposed Control Architecture

The researchers developed a two-layer control system designed for rapid response and computational efficiency.

Overall control architecture including the TSMCr upper layer and the constrained distributor lower layer.

Upper Layer: Terminal Sliding Mode Control (TSMCr)

The upper layer utilizes Terminal Sliding Mode Control (TSMC) rather than standard linear sliding surfaces. By employing nonlinear sliding manifolds, the system ensures that tracking errors for longitudinal velocity, lateral velocity, and yaw rate reach zero within a guaranteed finite time. This rapid responsiveness is vital for stabilizing the vehicle during emergency maneuvers.

Lower Layer: Constrained Torque Distributor

To manage the distribution of forces to the wheels, a logic-based distributor was implemented. Unlike high-overhead optimization algorithms, this distributor uses a pseudo-inverse method for real-time performance. It incorporates a "constrained" logic that monitors tire adhesive limits (the friction circle). If tires reach their limits, the system prioritizes yaw stability ($M_{zd}$) over longitudinal force to prevent vehicle spin.

Flowchart of the logic-based torque distribution strategy considering tire adhesive limits.

Simulation and Evaluation

The system was evaluated using a high-fidelity CarSim model of an A-Class hatchback integrated with MATLAB/Simulink. Testing scenarios included open-loop step-steer maneuvers to test inherent stability, closed-loop double-lane-change (DLC) at 100 km/h using an Optimal Preview Acceleration (OPA) driver model, and $\mu$-split braking, where left and right wheels encounter different friction levels, simulating hazardous road conditions.

Key Results

The proposed Constrained TSMC significantly outperformed standard SMC and unconstrained control methods:

  • Tracking Accuracy: In step-steer tests, the Root Mean Square (RMS) yaw rate error for Constrained TSMC was 1.0641°/s, compared to 1.1395°/s for standard SMC.
  • Path Following: During the DLC maneuver, the TSMC-controlled vehicle maintained a lateral offset of only 0.1693 m, outperforming the SMC's 0.2023 m.
  • Braking Stability: On split-friction surfaces, the system achieved a stopping time of 8.25 seconds with a maximum lateral deviation of just 0.50 m, demonstrating superior stability compared to standard ABS-equipped vehicles.

Conclusion

The integration of Terminal Sliding Mode Control with a constrained torque distribution strategy provides a robust solution for IWD vehicle stability. By ensuring finite-time convergence and prioritizing critical stability objectives under tire saturation, the system enhances safety and responsiveness. Future work will explore fault-tolerant control for actuator failures and real-time estimation of road friction coefficients to further improve real-world applicability.

Summary updated

Abstract

This paper presents a torque distribution method for an individual-wheel drive vehicle, in which each wheel is controlled individually by its own electric motor. The terminal sliding mode technique is employed for the motion control so as to track the desired vehicle motion obtained by interpreting the driver's commands. Thus, finite-time convergence of the system's dynamic errors can be achieved on the terminal sliding manifolds, as compared to the well-used linear sliding surface. By considering nonlinear constraints of the tire adhesive limits, a simple yet effective distribution strategy is introduced to allocate the motion control efforts to each of the four wheels. Through the use of a high-fidelity CarSim full-vehicle model, vehicle stability and handling performance of the proposed controller is evaluated in both open-and closed-loop simulations.
BibTeX
@article{song2014terminal,
  author = {Pan Song and Changfu Zong and Masayoshi Tomizuka},
  title = {{A terminal sliding mode based torque distribution control for an individual-wheel-drive vehicle}},
  journal = {Journal of Zhejiang University. Science A},
  year = {2014},
  doi = {10.1631/jzus.a1400101},
}
Figure