A Switched-Line True Time Delay Unit for Wideband Phased Arrays Using Packaged RF MEMS Switches

David Thomas, Kai Wu, Y. Jay GuoSensors 2025 · DOI

TL;DR

This paper presents a practical, 4-bit true time delay unit (TDU) for wideband phased arrays, built entirely from off-the-shelf components on a standard PCB. By leveraging commercially available RF MEMS switches, they achieve broadband operation with low loss and minimal delay error, paving the way for more efficient and scalable beamforming in next-generation wireless systems.

What Problem Does This Paper Address?

Modern wireless systems, like 5G/6G and satellite communications, demand agile and wideband beamforming to handle increasing data rates and coverage needs. Electronically scanned arrays (ESAs) are key to this, but traditional phase-based beamforming suffers from "beam squint" and signal distortion at higher frequencies. True time delay units (TDUs) offer a solution by introducing frequency-independent delays, but their practical implementation has been hindered by challenges in size, cost, reliability, and manufacturability. Previous TDU approaches using photonic, MMIC, or distributed MEMS technologies have had their own trade-offs, such as complex integration, high insertion loss, or limited bandwidth. This paper aims to bridge this gap by demonstrating a TDU that is both high-performance and practical for widespread adoption.

Methods

The core of this work is a switched-line architecture for the TDU. This design uses transmission lines of varying lengths, with RF MEMS switches selecting which line is active to create discrete time delays. The TDU is built as a 4-bit unit, meaning it can achieve 16 different delay states, by cascading two 2-bit sections.

A key innovation is the use of commercially available, packaged RF MEMS SP4T switches (Menlo Micro MM5140). This avoids the need for custom MEMS fabrication, exotic substrates, or specialized assembly processes, making the design more manufacturable and cost-effective. The entire TDU is implemented on a standard multilayer PCB using conductor-backed coplanar waveguide (CBCPW) for its superior performance characteristics in wideband applications.

To address potential issues with unused delay lines causing resonances and group delay ripple, the authors employed a strategy of terminating unused paths to ground using separate shunt RF MEMS switches. This aims to emulate broadband matched terminations.

A significant part of the paper is dedicated to reconciling simulation and measurement results. Initially, simple lumped-element models for the switches led to discrepancies. The authors developed a more accurate 5-port multiport switch model that accounts for the actual board environment and the behavior of the OFF-state switch ports, significantly improving the agreement between predicted and measured performance.

Datasets

Not discussed in the paper. The evaluation relies on measurements from the fabricated prototype and simulations.

Key Insights and Ideas

  • Commercial RF MEMS are viable for TDUs: The paper demonstrates that readily available, packaged RF MEMS switches can be effectively integrated into a high-performance TDU, lowering the barrier to entry for advanced beamforming systems.
  • PCB integration is key to manufacturability: By using standard PCB processes and off-the-shelf components, the TDU becomes practical for mass production, unlike many previous research prototypes.
  • OFF-path switch loading is a critical modeling challenge: The significant discrepancy between initial simulations and measurements was traced to the shunt loading effect of the unused switch ports. Accurately modeling this multiport behavior is crucial for predicting TDU performance.
  • Careful layout and grounding can mitigate resonance issues: While terminating unused lines helps, the paper suggests that good electromagnetic design practices, like using CBCPW and grounding vias, can effectively reduce coupling and reflections, potentially making explicit termination less critical.
  • Impedance matching is paramount: Even small deviations in impedance at switch-line interfaces can lead to significant ripple and increased insertion loss, highlighting the need for meticulous design and manufacturing.

Key Results

  • Broadband Operation: The TDU operates from 0.4 to 6 GHz.
  • 4-Bit Resolution: Achieves a maximum delay of 413 ps with a resolution of approximately 27.5 ps per bit.
  • Low Insertion Loss: Average insertion loss is 1.5 dB.
  • Low Delay Error: Mean absolute delay error is 18.4 ps.
  • Figure of Merit (FOM): Achieved an FOM of 152.8 ps/dB.
  • Return Loss: Measured return loss is better than 9 dB.
  • Simulation-Measurement Agreement: After incorporating the refined multiport switch model, simulation and measurement results show close agreement.

Limitations and Future Work

  • Footprint: The current design's footprint is larger compared to monolithic or MMIC solutions.
  • Fabrication Tolerances: Performance remains sensitive to fabrication tolerances.
  • Parasitic Loading: Packaged switches introduce parasitic loading, which affects performance.

Future work could focus on:

  • Reducing the footprint through multilayer or fractal delay-line geometries.
  • Improving impedance control and tightening process tolerances.
  • Investigating lower-parasitic switch packaging.
  • Further reducing group-delay ripple by accounting for multiport loading effects and optimizing impedance matching.
  • Exploring the combination of true time delay with phase control for joint phase-time adjustment (JPTA) for even finer beam steering.

Summary updated

Abstract

The growing demand for wideband electronically scanned arrays (ESAs) in next-generation radar, satellite, and 5G/6G systems has renewed interest in true time delay units (TDUs) to overcome the limitations of phase-based beamforming. In parallel, recent advances in the commercial availability and reliability of packaged RF MEMS switches have enabled practical hardware implementations once considered infeasible. This paper presents the design, fabrication, and experimental validation of a broadband, 4-bit switched-line TDU using only off-the-shelf components and standard PCB processes. The unit operates from 0.4 to 6 GHz, with a total delay range of 0-413 ps, achieving an average insertion loss of 1.5 dB and delay error below 18.4 ps, resulting in a figure of merit (FOM) of 152.8 ps/dB. Measured results are reported alongside a refined switch/termination model that aligns simulations with measurements. This is among the first reported demonstrations of a complete RF MEMS-based TDU implemented entirely with commercially available components in a standard PCB-integrated implementation. These results demonstrate a practical pathway toward scalable MEMS-based TDUs for deployment in advanced beamforming systems.
BibTeX
@inproceedings{thomas2025switched,
  author = {David Thomas and Kai Wu and Y. Jay Guo},
  title = {{A Switched-Line True Time Delay Unit for Wideband Phased Arrays Using Packaged RF MEMS Switches}},
  booktitle = {Sensors},
  year = {2025},
  doi = {10.3390/s25216806},
}
Figure