A Swash Mass Unmanned Aerial Vehicle: Design, Modeling and Control

Andrea M. Tonello, Babak SalamatarXiv 2019 · arXiv

Abstract

In this paper, a new unmanned aerial vehicle (UAV) structure, referred to as swash mass UAV, is presented. It consists of a double blade coaxial shaft rotor and four swash masses that allow changing the orientation and maneuvering the UAV. The dynamical system model is derived from the Newton's law framework. The rotational behavior of the UAV is discussed as a function of the design parameters. Given the uniqueness and the form of the obtained non-linear dynamical system model, a back-stepping control mechanism is proposed. It is obtained following the Lyapunov's control approach in each iteration step. Numerical results show that the swashed mass UAV can be maneuvered with the proposed control algorithm so that linear and aggressive trajectories can be accurately tracked.

Introduction

Traditional rotary-wing UAVs often face a trade-off between mechanical simplicity and aerodynamic maneuverability. Quadrotors are mechanically simple but limited in certain flight regimes, while traditional helicopters utilize complex swashplate mechanisms to adjust blade pitch—linkages that are difficult to scale down effectively. This paper introduces the Swash Mass UAV, a novel design that achieves high maneuverability through center-of-mass (CM) shifting rather than complex mechanical linkages.

Mechanical Design and Modeling

The Swash Mass UAV features a double-blade coaxial shaft rotor providing lift and yaw control. Maneuvering in pitch and roll is achieved by four movable masses positioned on orthogonal horizontal arms. By shifting these masses, the vehicle's center of mass moves relative to its geometric center (GC), creating the necessary moments for orientation changes.

A significant challenge in modeling this system is that the vehicle's inertia matrix is time-variant, as it depends on the instantaneous positions of the four swash masses. The authors derived a full non-linear dynamical model using Newton’s laws to account for these shifting dynamics and the resulting pendulum-like control behavior.

Control Strategy

Due to the under-actuated nature of the system (6 degrees of freedom controlled by 4 inputs), a non-linear back-stepping controller was developed. The control architecture is hierarchical, consisting of an external loop for position tracking and an internal loop for attitude control.

The controller employs Lyapunov’s stability theory at each iteration to ensure robust trajectory tracking. To manage the complexity of the time-variant inertia, the authors utilized a constant inertia approximation based on the mean mass positions, supplemented by a compensator to handle physical servo saturation limits where the masses reach the ends of their arms.

Results and Discussion

The design and controller were validated through numerical simulations of two primary flight scenarios:

  1. Linear Trajectory: The UAV demonstrated high precision in a straight-line ascent, achieving a root-mean-square error (RMSE) of approximately 0.3 meters.
  2. Aggressive Trajectory: A complex "figure-eight" path was used to test the limits of the CM-steering mechanism. The UAV maintained stability throughout the rapid orientation changes, with an overall RMSE of 0.35 meters.

Sensitivity analysis revealed that the maximum achievable pitch angle is highly dependent on design parameters such as arm length ($L$) and the mass ratio ($m/M$). Increasing these parameters enhances maneuverability, though physical constraints on the arm length impose practical limits on the vehicle's performance.

Conclusion

The Swash Mass UAV presents a mechanically robust alternative to traditional swashplate-based designs. While current results are simulation-based, they demonstrate the feasibility of using movable masses for aggressive flight maneuvers. Future work will focus on physical prototyping to account for real-world factors like aerodynamic interference between coaxial blades and servo latency.

Summary updated

Abstract

In this paper, a new unmanned aerial vehicle (UAV) structure, referred to as swash mass UAV, is presented. It consists of a double blade coaxial shaft rotor and four swash masses that allow changing the orientation and maneuvering the UAV. The dynamical system model is derived from the Newton\textquotesingle s law framework. The rotational behavior of the UAV is discussed as a function of the design parameters. Given the uniqueness and the form of the obtained non-linear dynamical system model, a back-stepping control mechanism is proposed. It is obtained following the Lyapunov's control approach in each iteration step. Numerical results show that the swashed mass UAV can be maneuvered with the proposed control algorithm so that linear and aggressive trajectories can be accurately tracked.
BibTeX
@misc{tonello2019swash,
  author = {Andrea M. Tonello and Babak Salamat},
  title = {{A Swash Mass Unmanned Aerial Vehicle: Design, Modeling and Control}},
  year = {2019},
  eprint = {1909.06154},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/1909.06154},
}
Figure