A Rotational Gyroscope with a Water-Film Bearing Based on Magnetic Self-Restoring Effect

Dianzhong Chen, Xiaowei Liu, Haifeng Zhang, Hai Li, Rui Weng, Ling Li, Wanting Rong, Zhongzhao ZhangSensors 2018 · DOI

TL;DR

This paper introduces a novel rotational gyroscope design that utilizes a water-film bearing for rotor support and a magnetic self-restoring effect for stability, eliminating the need for complex electrostatic suspension systems. This approach achieves a bias stability of 0.5°/h, offering a simpler and potentially more robust solution for high-precision angular rate sensing.

What Problem Does This Paper Address?

Traditional high-performance rotational gyroscopes, such as Magnetically Suspended Gyroscopes (MSGs) and Electrostatically Suspended Gyroscopes (ESGs), face significant challenges in achieving stable rotor levitation. This stability is crucial for improving performance but often requires intricate and costly pick-up circuits and feedback control electronics. These complex systems can be difficult to fabricate and may introduce limitations like air breakdown issues in ESGs. The paper aims to overcome these limitations by proposing a gyroscope that offers stable rotor support and inherent restoring forces without relying on complex active suspension mechanisms.

Methods

The core innovation lies in the combination of a water-film bearing and a magnetic self-restoring effect.

  • Water-Film Bearing: Instead of traditional magnetic or electrostatic levitation, this gyroscope uses a ball-disk shaped rotor supported by a thin film of deionized water. Centrifugal force from the spinning rotor creates this water film within a cavity in the lower supporting pillar, providing stable mechanical support with low friction.
  • Superhydrophobic Surface (SHS): To further reduce sliding friction between the rotor ball and the water-film bearing, a superhydrophobic surface with nano-structures was fabricated on the rotor ball. This significantly improves the rotor's ability to achieve higher spinning speeds.
  • Magnetic Self-Restoring Effect: The rotor is actuated by a brushless direct current motor (BLDCM) scheme. The interaction between the magnetized rotor and the stator generates a restoring torque that is inherently proportional to the rotor's deflection angle. This magnetic restoring torque acts to bring the rotor back to its stable position, negating the need for high-voltage electrostatic feedback systems.
  • Sensing: Input angular speeds are measured using two differential capacitance pairs, positioned to detect rotor plane deflection in perpendicular directions.

Datasets

Not discussed in the paper. The paper focuses on the design, fabrication, and experimental characterization of a single gyroscope prototype.

Key Insights and Ideas

  • Water as a Bearing Material: The paper demonstrates that a simple water film, generated by centrifugal force, can effectively provide stable and low-friction support for a high-speed rotor, simplifying gyroscope design significantly.
  • Passive Magnetic Restoration: Leveraging the inherent magnetic properties of the rotor and stator to create a self-restoring torque is a clever way to achieve stability without active feedback, reducing complexity and potential failure points.
  • SHS for Performance Boost: The application of a superhydrophobic surface not only reduces friction but also demonstrably increases the achievable spinning speed, leading to a higher angular momentum and improved gyroscope performance.
  • Integrated Design: The synergy between the water-film bearing, SHS, and magnetic self-restoring effect creates a robust and high-performance system from relatively simple components.

Key Results

  • Increased Spinning Speed: The SHS treatment resulted in a rated spinning speed increase of 12.4% (from 8970 rpm to 10,084 rpm) under the same driving current.
  • Bias Stability: The fabricated gyroscope achieved a bias stability as low as 0.5°/h.
  • Sensitivity and Linearity: The gyroscope demonstrated a low-frequency sensitivity of 0.0985 V/(°/s) and linearity within the tested range (-30°/s to 30°/s) of 0.43%.
  • Resolution: The resolution was confirmed to be 0.1°/s.
  • Dynamic Characteristics: Impulse response tests showed functionality comparable to a MEMS quartz vibratory gyroscope.

Limitations and Future Work

  • Measurement Range: The linearity of the differential capacitance detection is limited to rotor deflection angles within 1°, which restricts the measurement range of the gyroscope to approximately ±30°/s.
  • Noise Components: The spectral analysis revealed noise components at frequencies related to the driving frequency and rotor self-restoring effect, suggesting potential areas for further noise reduction.
  • Future Work: The authors suggest that further improvements could be made by optimizing the design to extend the measurement range and reduce noise. The paper also implicitly points towards exploring different liquid bearing materials or SHS fabrication techniques for even better performance.

Summary updated

Abstract

Stable rotor levitation is a challenge for rotational gyroscopes (magnetically suspended gyroscopes (MSG) and electrostatically suspended gyroscopes (ESG)) with a ring- or disk-shaped rotor, which restricts further improvement of gyroscope performance. In addition, complicated pick-up circuits and feedback control electronics propose high requirement on fabrication technology. In the proposed gyroscope, a ball-disk shaped rotor is supported by a water-film bearing, formed by centrifugal force to deionized water at the cavity of the lower supporting pillar. Water-film bearing provides stable mechanical support, without the need for complicated electronics and control system for rotor suspension. To decrease sliding friction between the rotor ball and the water-film bearing, a supherhydrophobic surface (SHS) with nano-structures is fabricated on the rotor ball, resulting in a rated spinning speed increase of 12.4% (under the same driving current). Rotor is actuated by the driving scheme of brushless direct current motor (BLDCM). Interaction between the magnetized rotor and the magnetic-conducted stator produces a sinusoidal rotor restoring torque, amplitude of which is proportional to the rotor deflection angle inherently. Utilization of this magnetic restoring effect avoids adding of a high amplitude voltage for electrostatic feedback, which may cause air breakdown. Two differential capacitance pairs are utilized to measure input angular speeds at perpendicular directions of the rotor plane. The bias stability of the fabricated gyroscope is as low as 0.5°/h.
BibTeX
@inproceedings{chen2018rotational,
  author = {Dianzhong Chen and Xiaowei Liu and Haifeng Zhang and Hai Li and Rui Weng and Ling Li and Wanting Rong and Zhongzhao Zhang},
  title = {{A Rotational Gyroscope with a Water-Film Bearing Based on Magnetic Self-Restoring Effect}},
  booktitle = {Sensors},
  year = {2018},
  doi = {10.3390/s18020415},
}
Figure