Abstract
Both electron and phonon transport properties of single layer MoS2 (SLMoS2) are studied. Based on first-principles calculations, the electrical conductivity of SLMoS2 is calculated by Boltzmann equations. The thermal conductivity of SLMoS2 is calculated to be as high as 116.8 Wm(-1) K(-1) by equilibrium molecular dynamics simulations. The predicted value of ZT is as high as 0.11 at 500 K. As the thermal conductivity could be reduced largely by phonon engineering, there should be a high possibility to enhance ZT in the SLMoS2-based materials.
Introduction
Thermoelectric materials, which convert waste heat into electricity, are evaluated by the dimensionless figure of merit, $ZT$. While graphene has dominated 2D materials research, its zero bandgap makes it a poor thermoelectric. Single-layer $MoS_2$ (SL$MoS_2$), a semiconductor with a direct bandgap, is a more promising candidate. However, previous theoretical studies on SL$MoS_2$ produced inconsistent results, with predicted $ZT$ values ranging from 0.5 to 3.4. Many earlier models used "ballistic" transport assumptions that ignored electron scattering, likely overestimating performance. This study provides a rigorous re-evaluation by accounting for scattering and using more reliable potential models for thermal calculations.
Methodology and Structural Model
The authors employed a multi-scale computational approach. Electronic structures were calculated using Density Functional Theory (DFT) via the QUANTUM ESPRESSO package. Transport coefficients, including the Seebeck coefficient ($S$) and electrical conductivity ($\sigma$), were derived by solving the Boltzmann Transport Equation (BTE) using the BoltzTrap code. Lattice thermal conductivity ($\kappa$) was calculated using Equilibrium Molecular Dynamics (EMD) simulations with the Green-Kubo approach in LAMMPS, utilizing the Stillinger-Weber potential.
The study generates data based on the atomic structure of $MoS_2$ with a lattice constant of approximately 3.13 Å. The results are validated against a meta-analysis of over 15 previous reports.
Electronic and Phonon Transport Properties
The band structure reveals a "Q-valley" along the $\Gamma$-K path, which yields a larger effective mass for carriers than the K-valley. This multi-valley structure is highly favorable for increasing $ZT$. Due to 2D quantum size effects, sharp gradients and peaks appear in the Density of States (DOS) near the band edges. Aligning the Fermi level with these peaks is crucial for optimizing the power factor.
The phonon dispersion relations (shown in Figure 6b) were accurately reproduced using the Stillinger-Weber potential, providing a more reliable basis for thermal conductivity calculations than previous studies.
Key Results and Discussion
The study found a high intrinsic thermal conductivity of 116.8 W/m·K at 300K for an infinite sheet, which decreases to 52.9 W/m·K at 500K due to increased Umklapp scattering. While high thermal conductivity usually hurts $ZT$, it presents an opportunity for "phonon engineering" (e.g., nanopores or isotope doping) to reduce it without significantly degrading electrical properties.
Optimized $ZT$ values were found to be 0.04 at 300K, 0.07 at 400K, and 0.11 at 500K. The power factor reaches several hundreds of $\mu$W/cm·K², comparable to high-performance bulk thermoelectrics like $Bi_2Te_3$. Only weak anisotropy was observed in thermal conductivity between the armchair and zigzag directions.
Conclusion
The intrinsic $ZT$ of 0.11 is below the commercial viability threshold of 1.0. However, the high baseline thermal conductivity suggests that introducing nanostructures to shorten the phonon mean free path could slash thermal conductivity by orders of magnitude. This potential for phonon engineering could push $ZT$ well above 1.0, making SL$MoS_2$-based materials highly competitive for thermoelectric applications.
Summary updated