A Positioning Alarm System for Explosive Impact Debris Protective Suit Based on an Accelerometer Array

Jianing Hu, Chaoran Liu, Xucong Wang, Zai Wang, Xin Tong, Fangqi Li, Zhenyu Jin, Xiaoyuan Wang, Lufeng Che, Jing Yu, Defei Yao, Gaofeng Wang, Linxi DongSensors 2024 · DOI

TL;DR

This paper introduces a novel wearable system for firefighters that uses an array of piezoelectric accelerometers to detect and pinpoint the location of injuries caused by explosive impact debris. The system provides real-time monitoring and alerts, significantly improving the ability to locate and rescue injured firefighters in hazardous environments.

What Problem Does This Paper Address?

Firefighting is an inherently dangerous profession, and while protective suits shield firefighters from burns, they offer little to no information about injuries sustained from impact debris. This lack of real-time injury localization makes it difficult for commanders to quickly assess the situation and direct rescue efforts effectively, potentially leading to delayed medical attention and worse outcomes for injured firefighters. The paper aims to bridge this gap by developing a smart protective suit that can precisely identify where a firefighter has been injured by debris.

Methods

The core of the system is a network of piezoelectric accelerometers embedded within a firefighter's protective suit. These sensors are strategically placed on vital body parts to detect vibrations caused by impacts. When an impact occurs, the piezoelectric sensors generate a charge proportional to the force, which is then amplified by a charge amplifier circuit. This amplified signal is processed by a microcontroller (STC8H8K64U) which utilizes a 12-bit ADC for data acquisition and a UART-DMA for efficient data transfer.

For real-time monitoring and visualization, the processed data is transmitted wirelessly via Bluetooth to an upper computer running LabVIEW. Here, a state machine-based software architecture handles data decoding and error correction. The system then visualizes the impact location and intensity on a 3D human model, allowing commanders to see exactly where a firefighter is injured. A key innovation is the use of DMA for accelerating data processing, reducing the system cycle time to 0.11 ms.

Datasets

Not discussed in the paper. The evaluation was performed on a dummy body model.

Key Insights and Ideas

  • Beyond passive protection: The research moves beyond traditional protective gear to create an active safety system that provides critical real-time information about the wearer's condition.
  • Piezoelectric sensors as impact detectors: Leveraging the piezoelectric effect for impact detection offers a sensitive and reliable method for capturing transient forces.
  • Charge amplification for signal integrity: Using charge amplifiers effectively mitigates the influence of parasitic capacitances, ensuring accurate signal measurement even with varying wire lengths.
  • DMA for ultra-fast response: The implementation of DMA significantly reduces data processing latency, enabling near-instantaneous detection and reporting of impacts.
  • 3D visualization for intuitive command: Presenting injury data on a 3D model provides an intuitive and easily understandable interface for fire commanders, crucial in high-stress situations.

Key Results

The developed system demonstrates:

  • High localization accuracy: A positional accuracy of 3.6 ± 0.1 cm was achieved on a dummy body model.
  • Rapid response time: The system boasts a response time of 0.11 ms, attributed to the smart signal processing with DMA.
  • Excellent sensor consistency: Under a maximum sinusoidal vibration acceleration of 7 g, the piezoelectric sensors exhibited consistent output voltage (23.7 ± 3.3 V).
  • Independent sensor operation: The 56 sensors on the dummy body model could operate independently without affecting each other.

Limitations and Future Work

The authors acknowledge that the current system's effective communication distance is limited to approximately 18 meters via Bluetooth. They suggest that incorporating a 4G module could improve this. Future work will focus on optimizing communication distance and exploring additional applications for this sensor system. The authors also note that the current testing was performed on a dummy body model, and real-world field testing with firefighters would be a logical next step.

Summary updated

Abstract

Protection suits are vital for firefighters' safety. Traditional protection suits physically protect firemen from burns, but cannot locate the position of bodily injuries caused by impact debris. Herein, we present a wearable impact debris positioning system for firefighter protection suits based on an accelerometer array. Wearable piezoelectric accelerometers are distributed regularly on the suit to detect the vibration on different body parts, which is conducive to determining the position of injured body parts. In addition, the injured parts can be displayed on a dummy body model on the upper computer with a higher localization accuracy of 4 cm. The positioning alarm system has a rapid response time of 0.11 ms, attributed to the smart signal processing method. This work provides a reliable and smart method for locating and assessing the position of bodily injuries caused by impact debris, which is significant because it enables fire commanders to rescue injured firefighters in time.
BibTeX
@inproceedings{hu2024positioning,
  author = {Jianing Hu and Chaoran Liu and Xucong Wang and Zai Wang and Xin Tong and Fangqi Li and Zhenyu Jin and Xiaoyuan Wang and Lufeng Che and Jing Yu and Defei Yao and Gaofeng Wang and Linxi Dong},
  title = {{A Positioning Alarm System for Explosive Impact Debris Protective Suit Based on an Accelerometer Array}},
  booktitle = {Sensors},
  year = {2024},
  doi = {10.3390/s24144587},
}
Figure