A New Omni-Directional EMAT for Ultrasonic Lamb Wave Tomography Imaging of Metallic Plate Defects

Songling Huang, Zheng Wei, Wei Zhao, Shen WangSensors 2014 · DOI

TL;DR

This paper introduces a novel omni-directional Electromagnetic Acoustic Transducer (EMAT) with a unique "contra-flexure coil" (CFC) design for improved ultrasonic Lamb wave (ULW) tomography imaging of defects in metallic plates. The new EMAT effectively transmits and receives a pure A0 mode ULW with a high signal-to-noise ratio, leading to more accurate defect detection and size estimation.

What Problem Does This Paper Address?

Metallic plates are ubiquitous in critical industries like aerospace and automotive, but they are susceptible to defects that can compromise safety. Traditional inspection methods are often slow and localized. Ultrasonic Lamb Wave (ULW) inspection offers a faster, more efficient way to scan large surfaces and detect these defects. However, accurately characterizing the size and shape of these defects requires advanced techniques like Tomography Imaging (TI). Existing ULW TI methods often struggle with generating pure ULW modes, leading to interference and reduced imaging quality. Furthermore, traditional omni-directional transducers can be cumbersome or have limitations in rapid scanning. This paper aims to address these challenges by developing a new, non-contacting, omni-directional EMAT that can generate and detect a purer ULW mode, thereby improving the accuracy and efficiency of ULW tomography for defect characterization.

Methods

The core innovation of this paper is the development of a new omni-directional EMAT featuring a contra-flexure coil (CFC). This CFC, constructed using PCB technology, is designed to generate and receive ULW signals. Unlike traditional coil structures, the CFC's annular wires are arranged such that eddy currents induced by adjacent wires travel in opposite directions. This design, when combined with a permanent magnet providing a bias magnetic field, causes the aluminum plate to vibrate in a way that preferentially excites and detects the A0 mode ULW. This selective excitation leads to a purer A0 mode signal with a higher signal-to-noise ratio (SNR).

For the tomography imaging itself, the paper employs the cross-hole method. In this approach, an array of EMATs is positioned on opposite sides of the area to be inspected. ULW rays are transmitted through the material from multiple angles, and their Time of Flight (TOF) is measured. Defects alter the material's properties, affecting the ULW's group velocity and thus its TOF. The paper utilizes the Simultaneous Iterative Reconstruction Technique (SIRT) algorithm to reconstruct an image of the material's slowness (the reciprocal of group velocity) from the collected TOF data, thereby revealing the location and extent of defects.

Datasets

The experiments were conducted on a 3 mm thick aluminum plate. Artificial corrosion defects were introduced for testing. The paper does not introduce new benchmark datasets but rather uses this controlled experimental setup to evaluate the performance of the proposed EMAT.

Key Insights and Ideas

  • The Contra-Flexure Coil (CFC) is Key: The novel CFC design is the central innovation, enabling the selective generation and reception of the A0 mode ULW. This purity is crucial for accurate signal processing in tomography.
  • Purer Signals, Better Imaging: By generating a purer A0 mode ULW with a higher SNR, the new EMAT significantly improves the accuracy of extracting projection data (like TOF) for tomography. This directly translates to better image quality and more reliable defect characterization.
  • Omni-directional without Rotation: The CFC design inherently allows for omni-directional transmission and reception, eliminating the need for complex mechanical rotation of transducers, which is a significant advantage for practical applications.
  • Circumferential Consistency is Sufficiently Good: While the irregular shape of the CFC does cause some distortion in the eddy current field, the impact on the circumferential consistency of the TOF projection data (which is critical for TI) is minimal. This suggests the EMAT is robust enough for practical use.
  • Resolution Scales with Transducer Count: The study analytically demonstrates that increasing the number of EMATs used in the array directly improves the reconstruction resolution, providing a clear path for optimizing imaging performance based on application needs.

Key Results

  • The new CFC EMAT successfully transmits and receives a pure single A0 mode ULW with a high signal-to-noise ratio (SNR).
  • Experimental results on a 3 mm thick aluminum plate showed that the estimated size of an artificial corrosion defect agreed well with its actual value.
  • The circumferential consistency of the TOF projection data was only slightly influenced by the CFC's irregular shape, with an evaluation index of dT = 4.8% for transmitter direction and dT' = 3.0% for receiver direction.
  • The amplitude consistency (dV) showed a higher variation (dV = 51.1% and dV' = 57.0%), but this is less critical for TOF-based tomography.
  • The ULW TI experiment successfully located and determined the size of an artificial defect (30 mm diameter, 2 mm deep) with an estimated size of approximately 4 cm, which is close to the actual size.
  • The paper analyzes the relationship between reconstruction resolution and the number of EMATs, showing that resolution can be improved by increasing the transducer count.

Limitations and Future Work

  • Amplitude Variation: The paper acknowledges that the amplitude of the transmitted and received ULW pulses distributes unevenly by 360° due to the CFC's shape irregularity. While this doesn't significantly impact TOF-based tomography, it could be a limitation for amplitude-based imaging techniques.
  • "Shadow Effect": The study notes that the reconstruction shape of the defect can be affected by the ULW rays passing by it, leading to an "elongated shape" or "shadow effect" in areas with low ray density. This is a common challenge in tomography and suggests that optimizing ray coverage is important.
  • Future Work: The authors suggest that increasing the number of EMATs used can improve reconstruction resolution, indicating that further experiments with denser arrays could yield even better results. The paper also implies that further investigation into optimizing the CFC design to minimize amplitude variations could be beneficial.

Summary updated

Abstract

This paper proposes a new omni-directional electromagnetic acoustic transducer (EMAT) for the ultrasonic Lamb wave (ULW) tomography imaging (TI) of defects in metallic plates. The proposed EMAT is composed of a permanent magnet and a coil with a contra-flexure structure. This new EMAT coil structure is used for omni-directional ULW transmission and reception and ULW TI for the first time. The theoretical background and the working principles of this EMAT are presented and analyzed. The experimental results of its use on a 3 mm thick aluminum plate indicate that the EMAT with a contra-flexure coil (CFC) can transmit and receive a pure single A0 mode ULW with a high signal-to-noise ratio (SNR). Thus, the extraction of the projection data used for ULW TI may be performed accurately. The circumferential consistency of the projection data is only slightly influenced by the distortion of the eddy current field that is induced by the new CFC with an irregular shape. When the new EMAT array is used for ULW TI using the cross-hole method and SIRT arithmetic, a desirable imaging quality can be achieved, and the estimated size of an artificial corrosion defect agreed well with its actual value. The relation between the reconstruction resolution and the number of the new EMATs used is analyzed. More TI experiments are carried out when the aluminum plate defect is in two different locations relative to the EMAT array, for the further investigation of the performances of the new EMATs.
BibTeX
@inproceedings{huang2014new,
  author = {Songling Huang and Zheng Wei and Wei Zhao and Shen Wang},
  title = {{A New Omni-Directional EMAT for Ultrasonic Lamb Wave Tomography Imaging of Metallic Plate Defects}},
  booktitle = {Sensors},
  year = {2014},
  doi = {10.3390/s140203458},
}
Figure