A Neural Coordination Strategy for Attachment and Detachment of a Climbing Robot Inspired by Gecko Locomotion

Binghe Wang, Zhouyi Wang, Yifan Song, Weijia Zong, Linghao Zhang, Keju Ji, Poramate Manoonpong, Zhendong DaiCyborg 2023 · DOI

TL;DR

This paper introduces a novel neural control strategy for a hybrid pneumatic-electric climbing robot, inspired by gecko locomotion. By mimicking the rhythmic attachment-detachment behavior of gecko toes and limbs, the robot achieves significantly improved adhesion and climbing performance compared to traditional control methods.

What Problem Does This Paper Address?

Current bionic climbing robots often struggle with agility, stability, and energy efficiency, especially when adapting to various substrates. A key limitation is the lack of sophisticated control for active attachment and detachment mechanisms, which are crucial for efficient climbing. While animals like geckos exhibit remarkable climbing skills due to their flexible toes and coordinated limb movements, replicating this in robots presents challenges: controlling the complex mechanics of active feet, managing hybrid drive systems with different response times, and achieving seamless coordination between limbs and feet, particularly accounting for the inherent hysteresis in pneumatic actuators.

Methods

The researchers developed a modular neural control framework inspired by gecko locomotion. This framework consists of four key modules:

  • Central Pattern Generator (CPG) Module: Generates basic rhythmic signals for periodic oscillation, mimicking biological neural circuits.
  • Post-processing CPG (PCPG) Module: Converts CPG signals into a format suitable for the robot's actuators.
  • Hysteresis Delay Line (DL) Module: Crucial for establishing coordination between the adhesion (pneumatic) and motion (electric) systems, and managing phase relationships between limbs. This module is key to compensating for actuator hysteresis.
  • Actuator Signal Conditioning Module: Adjusts signals to match the specific mechanical and electronic properties of the robot's actuators.

The control strategy focuses on mimicking the rhythmic, phase-shifted coordination observed in geckos, where limb movement and toe attachment/detachment occur in a synchronized, yet not strictly sequential, manner. This approach aims to overcome the limitations of simple sequential control and manage the inherent delays and hysteresis in the hybrid drive system.

Datasets

Not discussed in the paper. The paper focuses on experimental validation using a custom-built robot and gecko locomotion data.

Key Insights and Ideas

  • Gecko-inspired Rhythmic Coordination is Key: The study highlights that simply mimicking gecko foot structure isn't enough; replicating the rhythmic coordination between limb movement and toe attachment/detachment is critical for enhanced climbing performance.
  • Hysteresis as an Advantage: Instead of solely fighting actuator hysteresis, the neural control system leverages it through the Delay Line module to achieve variable phase relationships, enabling better limb-foot coordination.
  • Modular Neural Control for Hybrid Systems: The proposed modular framework effectively integrates different drive systems (pneumatic and electric) and addresses their distinct response characteristics and control challenges.
  • Adhesion Area is a Proxy for Force: The research demonstrates a strong correlation between the measured adhesion area and the potential adhesion force, allowing for indirect measurement and comparison of adhesion performance.

Key Results

  • Adhesion Area Improvement: The robot with the neural control strategy achieved a 285% larger adhesion area compared to a conventional algorithm.
  • Climbing Performance Boost: In plane/arc climbing scenarios, the coordinated robot showed a 150% increase in performance compared to the uncoordinated one, attributed to higher adhesion reliability.
  • Improved Stability and Speed: The neural control system (NCS) significantly improved the robot's climbing stability and speed. On a 45° slope, the NCS-controlled robot achieved a velocity of 0.4 cm/s, compared to 0.16 cm/s for the uncoordinated robot.
  • Enhanced Load Capacity: The robot with NCS demonstrated a maximum load capacity of 200 g on a 45° plane, significantly higher than the 50 g capacity of the uncoordinated robot.

Limitations and Future Work

  • Hysteresis Compensation: While the study effectively uses hysteresis, the authors acknowledge that the robot's response time for pneumatic toes (400 ms for adhesion, 300 ms for detachment) is still much slower than geckos (15-20 ms).
  • Sensing Limitations: A current drawback is the lack of direct sensing of the attachment-detachment state, which limits real-time regulation.
  • Force Distribution: The paper notes that optimizing limb force distribution during the stance phase requires further work.
  • Computational Power: Real-time calculation of optimal foot-end forces, a theoretically feasible solution for quadruped robots, is currently limited by the climbing robot's central controller's arithmetic power.
  • Mass-to-Length Ratio: The robot's current mass-to-length ratio is considered too large, impacting its maximum climbing angle.

Future work will focus on incorporating force sensing systems, upgrading the NCS for better state sensing and regulation, and developing low-complexity methods for stance-phase limb force distribution. Improving the robot's mechanics, particularly reducing its mass-to-length ratio and increasing pneumatic actuator speed, is also a key area for future development.

Summary updated

Abstract

Climbing behavior is a superior motion skill that animals have evolved to obtain a more beneficial position in complex natural environments. Compared to animals, current bionic climbing robots are less agile, stable, and energy-efficient. Further, they locomote at a low speed and have poor adaptation to the substrate. One of the key elements that can improve their locomotion efficiency is the active and flexible feet or toes observed in climbing animals. Inspired by the active attachment-detachment behavior of geckos, a hybrid pneumatic-electric-driven climbing robot with active attachment-detachment bionic flexible feet (toes) was developed. Although the introduction of bionic flexible toes can effectively improve the robot's adaptability to the environment, it also poses control challenges, specifically, the realization of attachment-detachment behavior by the mechanics of the feet, the realization of hybrid drive control with different response characteristics, and the interlimb collaboration and limb-foot coordination with a hysteresis effect. Through the analysis of geckos' limbs and foot kinematic behavior during climbing, rhythmic attachment-detachment strategies and coordination behavior between toes and limbs at different inclines were identified. To enable the robot to achieve similar foot attachment-detachment behavior for climbing ability enhancement, we propose a modular neural control framework comprising a central pattern generator module, a post-processing central pattern generation module, a hysteresis delay line module, and an actuator signal conditioning module. Among them, the hysteresis adaptation module helps the bionic flexible toes to achieve variable phase relationships with the motorized joint, thus enabling proper limb-to-foot coordination and interlimb collaboration. The experiments demonstrated that the robot with neural control achieved proper coordination, resulting in a foot with a 285% larger adhesion area than that of a conventional algorithm. In addition, in the plane/arc climbing scenario, the robot with coordination behavior increased by as much as 150%, compared to the incoordinated one owing to its higher adhesion reliability.
BibTeX
@inproceedings{wang2023neural,
  author = {Binghe Wang and Zhouyi Wang and Yifan Song and Weijia Zong and Linghao Zhang and Keju Ji and Poramate Manoonpong and Zhendong Dai},
  title = {{A Neural Coordination Strategy for Attachment and Detachment of a Climbing Robot Inspired by Gecko Locomotion}},
  booktitle = {Cyborg},
  year = {2023},
  doi = {10.34133/cbsystems.0008},
}
Figure