TL;DR
This paper introduces a simplified and more portable method for measuring the emissivity of materials in the infrared spectrum. By using two closely spaced temperature points and a clever approximation, it eliminates the need for a reference blackbody, reducing complexity and cost while maintaining good accuracy.
What Problem Does This Paper Address?
Accurately measuring the emissivity of materials is crucial for various applications, from thermal management to remote sensing. Traditional methods often rely on reference blackbodies to account for background radiation. However, this assumption that background radiation is constant can lead to significant errors, especially in practical, non-ideal environments where background conditions can fluctuate. Existing two-temperature calibration methods also often require complex setups or multiple blackbodies, increasing cost and complexity. This paper aims to address these limitations by proposing a modified two-temperature calibration method that is simpler, more portable, and doesn't require a reference blackbody, while still effectively handling background radiation.
Methods
The core of the proposed method lies in a modified two-temperature calibration approach. Instead of using widely separated temperatures or multiple blackbodies, the authors set two measurement temperatures (T₁ and T₂) for the sample within a small interval. The key assumption is that over this short interval, the sample's emissivity, the background radiation reflected by the sample, and the stray radiation from the environment remain approximately constant.
This allows the researchers to derive an equation for emissivity that relies solely on the measured radiant signals from the sample at these two temperatures, and the known Planck's law radiance of an ideal blackbody at those same temperatures. Crucially, this formulation bypasses the need for a direct measurement of the background radiation or the use of a reference blackbody. The method involves:
- Determining Temperature Interval (ΔT): Based on the uncertainty of the radiant thermometer and an estimated emissivity, a suitable ΔT is calculated. This interval is designed to be large enough to distinguish between the two temperature measurements but small enough to satisfy the approximation assumptions.
- Measuring Radiant and Contact Temperatures: The sample is heated to T₁ and T₂, and for each temperature, both the radiant temperature (measured by the infrared thermometer) and the contact temperature (measured by a platinum resistance thermometer) are recorded.
- Calculating Emissivity: Using the recorded temperatures and the derived equation (Equation 10 in the paper), the emissivity of the sample is calculated.
An experimental facility was built to implement this method, featuring a heater, a sample holder, a contact thermometer, and an infrared radiant thermometer. A light trap was incorporated to minimize stray radiation and air convection.
Datasets
Not discussed in the paper. The study focuses on developing and validating a measurement method using controlled experiments with manufactured samples.
Key Insights and Ideas
- Eliminating the Blackbody Dependency: The most significant insight is the development of a method that bypasses the need for a reference blackbody. This drastically simplifies the experimental setup, making it more portable and cost-effective.
- The Power of Small Temperature Intervals: By carefully selecting two closely spaced temperatures, the authors leverage the assumption that emissivity and background radiation are relatively stable over short durations. This is a clever way to isolate the sample's emitted radiation.
- Handling Background Radiation Implicitly: Instead of directly measuring and subtracting background radiation, the method implicitly accounts for it by comparing the change in signal between two temperatures. This is a more robust approach when background conditions are not perfectly stable.
- Suitability for Temperature-Insensitive Samples: The method's core assumption makes it particularly well-suited for materials whose emissivity doesn't change significantly with small temperature variations.
Key Results
The developed method was tested on three samples with estimated emissivities of approximately 0.100, 0.500, and 0.900 in the (8-14) µm wavelength range.
- Low Relative Expanded Uncertainties: The method achieved good accuracy, with relative expanded uncertainties (k=2) of:
- 9.6% (sample 1, 60 °C), 8.8% (sample 1, 85 °C)
- 4.0% (sample 2, 60 °C), 5.8% (sample 2, 85 °C)
- 1.5% (sample 3, 60 °C), 1.2% (sample 3, 85 °C)
- Consistency with Other Methods: The results obtained using the developed method showed good consistency with those measured using an indirect method (reflectance-based) and a conventional two-temperature calibration method (which uses a blackbody). This was quantitatively supported by low "En" values, indicating agreement between the different measurement techniques.
- Effectiveness Demonstrated: The experimental results confirmed the effectiveness of the proposed modified two-temperature calibration method.
Limitations and Future Work
The authors acknowledge several limitations and suggest future research directions:
- Temperature Insensitivity Assumption: The method relies on the assumption that the sample's emissivity and background radiation are constant over the small temperature interval. This makes it most suitable for materials with temperature-insensitive emissivities. For materials with significant emissivity changes with temperature, this method might not be directly applicable.
- Narrow Spectral Window: The current setup uses a radiant thermometer with a narrow spectral window (8-14 µm). While they addressed this by using a standard body for calibration and gray body samples, future work could involve using an FTIR with a wider wavelength range to re-evaluate the method.
- Future Facility Improvements: The authors suggest improving the developed facility for both normal/directional and hemispherical emissivity measurements.
- Addressing Spectral Window Issues: Further research is needed to develop specific formulas to overcome the limitations of narrow spectral windows when using the Stefan-Boltzmann law.
Summary updated