A Modifiedo-Phthalaldehyde Fluorometric Analytical Method for Ultratrace Ammonium in Natural Waters Using EDTA-NaOH as Buffer

Hongzhi Hu, Ying Liang, Shuo Li, Qing Guo, Chancui WuJournal of Analytical Methods in Chemistry 2014 · DOI

TL;DR

This paper presents a refined fluorometric method for measuring ultratrace ammonium in natural waters. By incorporating EDTA-NaOH as a buffer, the method overcomes precipitation issues at optimal pH, leading to significantly enhanced sensitivity and the ability to quantify ammonium at nanomolar levels without pre-concentration.

What Problem Does This Paper Address?

Accurate measurement of ammonium (NH₃/NH₄⁺) is crucial for understanding nitrogen cycling in aquatic ecosystems. While the o-phthalaldehyde (OPA) fluorometric method is known for its high sensitivity compared to other techniques like the indophenol blue method, a key challenge arises when trying to optimize the reaction pH for maximum fluorescence. The OPA-NH₃ reaction typically performs best at a high pH (around 11), but at these basic conditions, natural waters, especially seawater, can precipitate due to the presence of metal ions. To avoid this, previous methods often had to operate at a lower, less sensitive pH (around 9.3). This paper tackles the problem of achieving high sensitivity in ammonium determination in natural waters by addressing the precipitation issue at the optimal high pH.

Methods

The core of this work is a modification of the established OPA fluorometric method for ammonium determination. The key innovation is the use of an EDTA-NaOH buffer solution (R₂). Disodium ethylenediaminetetraacetate (EDTA) is a strong metal ion chelating agent. By adding EDTA, the researchers were able to maintain the reaction solution at a high pH (11.0-11.4) without the problematic precipitation of metal ions, which is a common issue in natural water samples.

The researchers optimized several experimental parameters using a univariate design:

  • Reagent concentrations: Optimal concentrations for OPA and sodium sulfite were determined.
  • Reaction time: A 50-minute reaction time at room temperature was found to be sufficient.
  • pH: The optimal pH range was identified as 10.80-11.70, with the final method operating between 11.0-11.4.
  • EDTA effect: The study specifically investigated the impact of EDTA on fluorometric intensity, finding it did not significantly affect the signal.

The spectral characteristics of the reaction product were also analyzed, confirming excitation at 361 nm and emission at 423 nm, consistent with previous findings. A crucial step to reduce reagent blank involved passing the mixed OPA and sodium sulfite solution through an HLB cartridge to remove any pre-existing ammonium.

Datasets

The study utilized standard ammonium solutions for method development and optimization. For validation, they analyzed:

  • Freshwater samples from the Huajian River.
  • Groundwater and mountain spring water samples.
  • A surface seawater sample from the South China Sea.

These samples were used for recovery studies and intercomparison with other methods. No new benchmark datasets were introduced; rather, existing natural water samples were used to evaluate the performance of the proposed method.

Key Insights and Ideas

  • EDTA as a game-changer for high-pH ammonium analysis: The most significant insight is how effectively EDTA can prevent metal ion precipitation at high pH. This allows the OPA reaction to be conducted under its most sensitive conditions without compromising sample integrity.
  • Enhanced sensitivity without enrichment: The modified method achieves a detection limit of 0.0099 µmol/L, enabling the quantification of ultratrace ammonium levels (down to nanomolar) directly from natural water samples, eliminating the need for cumbersome pre-concentration steps.
  • Robustness across water types: The method demonstrated good recovery rates (97.60% to 103.83%) in various water matrices (freshwater, groundwater, seawater), indicating its broad applicability.
  • Reagent blank reduction is critical: The authors highlight the importance of reducing reagent blank by pre-treating the OPA and sulfite solution, which is essential for accurate ultratrace analysis.

Key Results

  • Optimal pH range: 10.80-11.70.
  • Method detection limit: 0.0099 µmol/L.
  • Linearity ranges:
    • 0.032-0.500 µmol/L (3 nm/5 nm slits)
    • 0.250-3.00 µmol/L (3 nm/3 nm slits)
    • 1.00–20.0 µmol/L (1.5 nm/1.5 nm slits)
  • Sensitivity improvement: The proposed method's slope (1237.6) was approximately four times higher than the classical OPA method's slope (312.6), indicating significantly better sensitivity.
  • Reproducibility: A relative standard deviation of 3.2% was achieved for a 0.250 µmol/L ammonium standard solution.
  • Intercomparison: The proposed method showed good agreement with the indophenol blue method for river water samples, with a wide concentration range (0.44 to 38.25 µmol/L). It also showed no statistically significant difference compared to the classical OPA method for seawater samples.

Limitations and Future Work

  • Limitations:
    • The paper mentions that the reagent blank can slowly increase over time due to ambient air, suggesting the need for daily preparation of the fluorescent reagent for optimal results.
  • While the method is sensitive, the linearity ranges vary depending on the slit widths used, requiring selection of the appropriate range for the expected sample concentration.
  • Future Work: The paper implicitly suggests that this method is ready for application in environmental monitoring. Further work could involve broader validation across a wider range of environmental conditions and potential integration into automated or field-deployable systems, building on the foundation of enhanced sensitivity and robustness.

Summary updated

Abstract

In the existence of appropriate amount of disodium ethylenediaminetetraacetate (EDTA), precipitation would not occur in seawater and other natural waters even if the sample solution was adjusted to strong basicity, and the NH3-OPA-sulfite reaction at the optimal pH range could be used to determine ammonium in natural waters. Based on this, a modified o-phthalaldehyde fluorometric analytical method has been established to determine ultratrace ammonium in natural waters. Experimental parameters, including reagent concentration, pH, reaction time, and effect of EDTA, were optimized throughout the experiments based on univariate experimental design. The results showed that the optimal pH range was between 10.80 and 11.70. EDTA did not obviously affect the fluorometric intensity. The linearity range of the proposed method was 0.032-0.500 µmol/L, 0.250-3.00 µmol/L, and 1.00-20.0 µmol/L at the excitation/emission slit of 3 nm/5 nm, 3 nm/3 nm, and 1.5 nm/1.5 nm, respectively. The method detection limit was 0.0099 µmol/L. Compared to the classical OPA method, the proposed method had the advantage of being more sensitive and could quantify ultratrace ammonium without enrichment.
BibTeX
@article{hu2014modified,
  author = {Hongzhi Hu and Ying Liang and Shuo Li and Qing Guo and Chancui Wu},
  title = {{A Modified<i>o</i>-Phthalaldehyde Fluorometric Analytical Method for Ultratrace Ammonium in Natural Waters Using EDTA-NaOH as Buffer}},
  journal = {Journal of Analytical Methods in Chemistry},
  year = {2014},
  doi = {10.1155/2014/728068},
}
Figure