A Lever Coupling Mechanism in Dual-Mass Micro-Gyroscopes for Improving the Shock Resistance along the Driving Direction

Yang Gao, Hongsheng Li, Libin Huang, Hui Sun2017 · DOI

TL;DR

This paper introduces a novel "lever coupling mechanism" for dual-mass micro-gyroscopes that significantly enhances their resistance to shock impacts along the driving direction. By cleverly altering the stiffness characteristics, the mechanism increases the frequency separation between the in-phase and anti-phase modes, leading to a dramatic reduction in shock-induced displacement and stress without compromising the gyroscope's sensitivity.

What Problem Does This Paper Address?

Micro-gyroscopes are essential components in many fields, from automotive to aerospace, but their delicate silicon structures are highly susceptible to damage from shock impacts. These shocks can cause catastrophic failures like stiction, electric shorts, or mechanical fractures due to excessive displacement and stress. While existing solutions like stoppers or structural reinforcements offer some protection, they often come with trade-offs, such as reduced sensitivity or increased complexity. A key challenge for dual-mass gyroscopes with drive-mode coupling is that their in-phase and anti-phase mode frequencies are often too close, making them vulnerable to shock. This paper aims to address this by developing a coupling mechanism that can effectively decouple these modes and improve shock resilience without sacrificing performance.

Methods

The researchers propose a "lever coupling mechanism" that modifies the stiffness of the dual-mass structure. This mechanism consists of levers, a tuning fork structure, and a double-ended beam, designed to create a significant difference between the in-phase and anti-phase coupling stiffness.

The paper employs a multi-pronged approach:

  • Theoretical Analysis: The mechanical sensitivity and shock response of a standard dual-mass gyroscope are analyzed using dynamic equations.
  • Finite Element Method (FEM): ANSYS software is used extensively for modal analysis, thermal analysis, and transient dynamic analysis to simulate the behavior of both the proposed (Type-B) and a traditional (Type-A) gyroscope structures under various conditions.
  • Analytical Solutions: For shock response, an analytical solution derived from modal superposition is presented and validated against FEM results.
  • Parameter Optimization: The influence of various geometric parameters of the lever coupling mechanism on stiffness ratios is investigated to optimize its performance.

Datasets

Not discussed in the paper. The study relies on simulations and theoretical analysis rather than experimental datasets from external sources.

Key Insights and Ideas

  • Stiffness Ratio is Key: The core idea is that by creating a large difference between the in-phase and anti-phase stiffness (and thus frequencies), shock resistance can be dramatically improved. The lever coupling mechanism achieves this by altering how forces are transmitted between the proof masses.
  • Modal Order Manipulation: The lever coupling mechanism effectively "switches" the modal order, making the in-phase frequency significantly higher than the anti-phase frequency. This is crucial for shock resistance.
  • Shock Response Reduction: The proposed mechanism reduces shock-induced displacement by over an order of magnitude and decreases impact stress by approximately 35.5% compared to traditional elastic coupling.
  • Sensitivity Preservation: A critical advantage is that this improved shock resistance is achieved without any loss in the gyroscope's mechanical sensitivity.
  • Simplified Processing: Compared to other advanced coupling structures like ring or diamond designs, the lever coupling mechanism is described as simpler and easier to fabricate.
  • Thermal Performance: Despite its increased complexity, the proposed structure's temperature performance is comparable to the traditional design, indicating no significant degradation.

Key Results

  • Shock Resistance: The improved gyroscope (Type-B) can withstand a 2500 g shock load, a significant increase from the traditional design (Type-A), which fails below 440 g.
  • Frequency Separation: The in-phase mode frequency of the Type-B gyroscope is approximately 176% higher than its anti-phase mode frequency, compared to a much smaller difference in the Type-A structure.
  • Displacement Reduction: Under a 100 g shock, the peak displacement of Type-B is reduced to 0.2294 µm (analytic) / 0.2414 µm (FEM), compared to 4.604 µm (analytic) / 4.584 µm (FEM) for Type-A.
  • Stress Reduction: Stress levels in Type-B are significantly lower than in Type-A under maximum impact displacement.

Limitations and Future Work

  • Driving Direction Focus: The current design primarily enhances shock resistance along the driving direction. The authors acknowledge that improving shock resistance in the sensing direction would require separate strategies like stoppers or beam optimization.
  • Drive-Sense Coupling: The paper focuses on dual-mass gyroscopes with drive-mode coupling. For gyroscopes with coupled drive and sense modes, research into sense-mode coupling mechanisms is suggested for future work.
  • Experimental Validation: While extensive simulations and analytical work are presented, the paper does not detail experimental validation of the proposed mechanism. This would be a crucial next step.

Summary updated

BibTeX
@misc{gao2017lever,
  author = {Yang Gao and Hongsheng Li and Libin Huang and Hui Sun},
  title = {{A Lever Coupling Mechanism in Dual-Mass Micro-Gyroscopes for Improving the Shock Resistance along the Driving Direction}},
  year = {2017},
  doi = {10.3390/s17050995},
}

Loading related content...

Figure