A Highly Sensitive CMOS Digital Hall Sensor for Low Magnetic Field Applications

Yue Xu, Hong‐Bin Pan, Shuzhuan He, Li LiSensors 2012 · DOI

TL;DR

This paper presents a highly sensitive CMOS digital Hall sensor designed for low magnetic field applications. By employing a novel dynamic offset cancellation technique and a simplified signal conditioner, the sensor achieves a remarkable sensitivity of 310 V/AT and can detect magnetic fields as low as ±2 mT across a wide temperature range.

What Problem Does This Paper Address?

Integrated CMOS Hall sensors are attractive for their small size, low cost, and compatibility with other CMOS technologies, making them suitable for a wide range of applications like industrial control, intelligent instruments, and consumer electronics. However, existing CMOS Hall sensors suffer from two major drawbacks: low magnetic field sensitivity and a significant offset voltage. This low sensitivity means they struggle to detect weak magnetic fields, while the offset voltage, caused by factors like process variations, temperature drift, and mechanical stress, can easily mask the actual Hall signal. These limitations restrict the minimum detectable magnetic field and the accuracy of measurements.

Methods

The authors introduce a highly sensitive digital Hall sensor built using 0.18 µm high voltage (HV) CMOS technology. The core of their approach involves two key innovations:

  • Optimized Cross-Shaped Hall Plate: They utilize a cross-shaped Hall plate, known for its good sensitivity and low offset. To further enhance performance, they employ a HV CMOS process which allows for a lower N-well doping concentration, leading to higher current-related sensitivity. The geometrical design of the Hall plate is also optimized (W/L = 2) to balance sensitivity and offset reduction.
  • Novel Signal Conditioner with Dynamic Offset Cancellation: The sensor incorporates a "chopper stabilized instrumental chain" for dynamic offset cancellation. This technique, based on the "spinning current" method, periodically interchanges the Hall plate's supply and output terminals. This effectively "chops" the Hall signal and separates it from the static offset and low-frequency 1/f noise. The chopped signal is then amplified by a differential instrumentation amplifier. Crucially, instead of traditional sample-and-hold circuits, they use two high-pass filters to remove the offset and 1/f noise, followed by a switched hysteresis comparator to generate the digital output. This simplified structure reduces chip area and complexity.

Datasets

Not discussed in the paper. The authors rely on simulation models and experimental measurements from their fabricated chip.

Key Insights and Ideas

  • HV CMOS for Enhanced Sensitivity: Utilizing a high-voltage CMOS process, which allows for lower doping concentrations in the N-well, is a direct pathway to achieving higher current-related sensitivity in Hall sensors.
  • Dynamic Offset Cancellation is Key: The spinning current technique, combined with high-pass filtering, is highly effective at removing both the Hall plate's intrinsic offset and the instrumentation amplifier's offset and 1/f noise, which are major hurdles in low-field sensing.
  • Simplified Signal Conditioning: Replacing complex sample-and-hold circuits with high-pass filters and a switched hysteresis comparator significantly reduces the chip area and cost of the signal conditioning chain, while maintaining performance.
  • Hysteresis without a Schmitt Trigger: The switched hysteresis comparator provides the necessary hysteresis for a digital Hall sensor without requiring a dedicated Schmitt trigger, further simplifying the design.

Key Results

  • High Current-Related Sensitivity: The proposed Hall plate achieves a current-related sensitivity of 310 V/AT, which is significantly higher than reported CMOS Hall devices (e.g., 90-180 V/AT).
  • Low Detectable Magnetic Field: The sensor can measure a minimum magnetic field of ±2 mT.
  • Wide Operating Temperature Range: The sensor operates reliably over a broad temperature range of -40 °C to 120 °C.
  • Low Offset: A small Hall offset of approximately 1 mV was measured at room temperature.
  • Robustness: The sensor works well with supply voltages from 2 V to 4 V.

Limitations and Future Work

  • Minimum Detectable Field Limit: The authors note that further improving the minimum detection sensitivity below ±2 mT is challenging without compromising the anti-jamming ability of the hysteresis comparator. Reducing the threshold voltage of the comparator could improve sensitivity but might lead to false triggering.
  • Parasitic Spikes: Simulations showed parasitic spikes during switching due to non-idealities. While they reduced switch size and employed a smaller Hall plate to mitigate these, further optimization might be needed for extremely sensitive applications.
  • Future Work: The paper suggests that this Hall sensor is well-suited for applications requiring small chip size and high sensitivity, such as integrated brushless DC motor drivers. Further integration and optimization for specific applications could be explored.

Summary updated

Abstract

Integrated CMOS Hall sensors have been widely used to measure magnetic fields. However, they are difficult to work with in a low magnetic field environment due to their low sensitivity and large offset. This paper describes a highly sensitive digital Hall sensor fabricated in 0.18 μm high voltage CMOS technology for low field applications. The sensor consists of a switched cross-shaped Hall plate and a novel signal conditioner. It effectively eliminates offset and low frequency 1/f noise by applying a dynamic quadrature offset cancellation technique. The measured results show the optimal Hall plate achieves a high current related sensitivity of about 310 V/AT. The whole sensor has a remarkable ability to measure a minimum ± 2 mT magnetic field and output a digital Hall signal in a wide temperature range from -40 °C to 120 °C.
BibTeX
@inproceedings{xu2012highly,
  author = {Yue Xu and Hong‐Bin Pan and Shuzhuan He and Li Li},
  title = {{A Highly Sensitive CMOS Digital Hall Sensor for Low Magnetic Field Applications}},
  booktitle = {Sensors},
  year = {2012},
  doi = {10.3390/s120202162},
}
Figure