A high-Q metasurface signal isolator for 1.5T surface coil magnetic resonance imaging on the go

Qun Ren, Yuxin Lang, Yuqi Ja, Xia Xiao, Yu Liu, Xiang Zheng Kong, Ruiqi Jin, Yongqing He, Jian Wei You, Wei E. I. Sha, Yanwei PangarXiv 2023 · DOI · arXiv

Abstract

The combination of surface coils and metamaterials remarkably enhances magnetic resonance imaging (MRI) performance, providing significant local staging flexibility. However, mutual coupling between these components often impedes the signal-to-noise ratio (SNR) and results in low-contrast resolution, hampering clinical growth. This paper proposes a high-Q metasurface decoupling isolator fueled by topological LC loops for 1.5T surface coil MRI systems. By employing a polarization conversion mechanism and bound states in the continuum (BIC), we effectively eliminate coupling between the MRI metamaterial and radio frequency (RF) surface coils, increasing the local magnetic field up to fivefold at 63.8 MHz. This study opens a promising route for portable and high-resolution surface coil MRI scanners.

Introduction

To achieve high-resolution MRI images, a high Signal-to-Noise Ratio (SNR) is essential. While traditionally achieved with massive superconducting magnets, a flexible alternative involves using surface coils combined with metamaterials—engineered structures that amplify magnetic fields locally. However, placing a surface coil near a metamaterial typically causes electromagnetic coupling, leading to signal interference and image artifacts. Standard shielding is ineffective as it blocks the desired signals. The challenge lies in achieving simultaneous signal enhancement while maintaining total isolation between components.

Methodology: Polarization Conversion and BIC

The proposed solution is a three-layer metasurface isolator designed to sit between the surface coil and the MRI metamaterial. The design relies on two primary physical mechanisms:

  1. Polarization Conversion: The isolator acts as an electromagnetic transformer, rotating the incident wave's polarization by 90 degrees. By making the fields of the coil and the metamaterial orthogonal (perpendicular) to each other, they become effectively "hidden" from one another, eliminating mutual interference.
  2. Bound States in the Continuum (BIC): To achieve high efficiency, the device requires an extremely high Quality factor (Q-factor). The researchers utilized symmetry-protected BIC, where waves are trapped within the structure. By introducing a specific 8mm asymmetry in the metal windings, they created a "quasi-BIC" state that produces a sharp, low-loss resonance at exactly 63.8 MHz.
Figure 4: Polarization conversion mechanism and transmission efficiency. (a) Schematic of X-P and Y-P planewave conversion. (b) Vector field maps showing isolation between the surface coil and metamaterial. (c) Transmission efficiency plots with and without the isolator.

Results and Discussion

The system was validated through full-wave electromagnetic simulations and equivalent LC circuit modeling. The most significant result was a fivefold increase in the magnetic field ($B_1$) at the target frequency of 63.8 MHz. The Polarization Conversion Ratio (PCR) exceeded 80% at the operating frequency, a dramatic improvement over the <20% observed without the isolator.

Figure 1: System overview and magnetic field enhancement. (a) Schematic of the surface coil, metasurface isolator, and MRI metamaterial. (b) H-field distribution maps and line plots comparing performance with and without the metasurface, demonstrating a 5x field boost.

In joint simulations using body phantoms (simulating human tissue properties), the magnetic field at the phantom surface was enhanced by 4 to 6 times. This collaborative enhancement allows the coil and metamaterial to work in harmony, producing a much stronger field than either could achieve independently.

Conclusion

This high-Q metasurface isolator successfully decouples MRI surface coils from enhancement metamaterials through polarization rotation and BIC physics. While the high-Q nature of the device makes it sensitive to frequency shifts caused by patient proximity—suggesting a role for future AI-driven real-time tuning—the current design provides a robust framework for miniaturized, high-performance MRI systems. This technology paves the way for the next generation of portable, "on the go" clinical MRI scanners.

Summary updated

Abstract

The combination of surface coils and metamaterials remarkably enhance magnetic resonance imaging (MRI) performance for significant local staging flexibility. However, due to the coupling in between, impeded signal-to-noise ratio (SNR) and low-contrast resolution, further hamper the future growth in clinical MRI. In this paper, we propose a high-Q metasurface decoupling isolator fueled by topological LC loops for 1.5T surface coil MRI system, increasing the magnetic field up to fivefold at 63.8 MHz. We have employed a polarization conversion mechanism to effectively eliminate the coupling between the MRI metamaterial and the radio frequency (RF) surface transmitter-receiver coils. Furthermore, a high-Q metasurface isolator was achieved by taking advantage of bound states in the continuum (BIC) for extremely high-field MRI and spectroscopy. An equivalent physical model of the miniaturized metasurface design was put forward through LC circuit analysis. This study opens up a promising route for the easy-to-use and portable surface coil MRI scanners.
BibTeX
@misc{ren2023high,
  author = {Qun Ren and Yuxin Lang and Yuqi Ja and Xia Xiao and Yu Liu and Xiang Zheng Kong and Ruiqi Jin and Yongqing He and Jian Wei You and Wei E. I. Sha and Yanwei Pang},
  title = {{A high-Q metasurface signal isolator for 1.5T surface coil magnetic resonance imaging on the go}},
  year = {2023},
  eprint = {2310.19846},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/2310.19846},
}
Figure