Abstract
When the fuel cell (FC) is being activated before used in industrial applications, a power conditioner is needed to interface the FC with the load. Due to low current ripples, high output power, and simple structure, the multi-phase interleaved non-isolated DC-DC converter is most suitable for the power conditioner. This paper proposed, analyzed and designed a four-phase interleaved buck-boost converter with changed load connection (CLC-FIBC) for the FC activation with characteristics as simple structure, wide input current, high current, and low current ripples. The operating principle and mathematical model of the CLC-FIBC were firstly analyzed, derived and presented, and then mathematical equations of transistor voltage stress and inductor current ripple are derived respectively. Besides, this CLC-FIBC was compared with several DC-DC converters to prove the superiority. The simulation and experimental prototype was built to validate the theoretical analysis after presenting some design considerations. Simulation and experimental results show that the CLC-FIBC has characteristics of both step up/down function, high power, wide input current range, and low current ripples.
Introduction
Before a fuel cell (FC) can be deployed in industrial applications, it must undergo an "activation" process to reach its peak performance. During this phase, the FC exhibits a "soft" volt-ampere characteristic, where its voltage drops significantly as the load current increases. To manage this behavior, a power conditioner—specifically a DC-DC converter—is required to interface the FC with a load.
The primary challenge for such a converter is the need to handle a wide range of input currents while providing both step-up and step-down voltage capabilities. Crucially, it must maintain extremely low current ripple, as high ripple can damage the sensitive membranes of the fuel cell. While traditional converters exist, they are often complex or suffer from high ripple and slow dynamic response.
Proposed Topology and Methodology
The researchers propose a Four-Phase Interleaved Buck-Boost Converter with Changed Load Connection (CLC-FIBC). This architecture relies on two key innovations:
- The Changed Load Connection (CLC) Trick: In a traditional boost converter, the load is connected between the output and ground. By moving the negative pole of the load to the input positive pole, a standard boost circuit is transformed into a buck-boost circuit. This allows for both step-up and step-down functionality without the need for additional switches, reducing cost and volume.
- Four-Phase Interleaving: The system utilizes four identical converter branches operating in parallel. By shifting their control signals (PWM) by 90 degrees, the current ripples from each phase partially cancel each other out, drastically reducing the total ripple seen by the fuel cell.
- Common Ground Configuration: The topology allows all four power transistors to share a common ground, which significantly simplifies the gate drive circuitry by eliminating the need for isolated power supplies for each switch.
Operating Principles and Ripple Analysis
Mathematical modeling of the CLC-FIBC revealed a "zero ripple" phenomenon. At specific duty cycles—namely 0.25, 0.5, and 0.75—the interleaved ripples theoretically cancel out completely. This provides exceptionally clean power to the fuel cell at these critical operating points. The derivation of mathematical equations for transistor voltage stress and inductor current ripple further supports the design's reliability under high-power conditions.
While the CLC topology results in a "floating load" (not connected to ground), this is acceptable for fuel cell activation, where the load is typically a dedicated resistive bank rather than an integrated vehicle powertrain component.
Experimental Results
The design was validated using MATLAB/Simulink simulations and a physical 40 kW hardware prototype utilizing Infineon IGBTs and a digital microcontroller. Key performance metrics include:
- High Power Density: The prototype successfully managed power levels up to 40 kW.
- Efficiency: The converter achieved a peak efficiency of 93%, which is highly competitive for high-power buck-boost topologies.
- Ripple Suppression: Total input current ripple was maintained below 6.2%, a significant improvement over standard non-interleaved designs.
- Versatility: The system demonstrated a wide input voltage range (0-700 VDC) and current range (0-300 A), proving its suitability for various fuel cell sizes.
Conclusion and Future Work
The CLC-FIBC offers a simple yet effective solution for fuel cell activation, combining high power capability with low current ripple. However, there are opportunities for further optimization. Future research could implement soft-switching technologies, such as Zero Voltage Switching (ZVS), to push efficiency beyond 93%. Additionally, optimizing magnetic core materials for the inductors could further reduce thermal losses, enhancing the overall performance of the power conditioner.
Summary updated